Ego Power+ CS2000E Manual página 9

B-1 Lock Nuts D-2
Chain-tensioning
B-2 E-1
Bolt
D-1 Chain Drive Links
NOTICE:
When looping the saw chain onto the guide
bar, make sure that, after mounting the guide bar onto
the saw, match the cutter pattern and rotation direction
arrow on the housing. If they face in opposite directions,
reassemble the saw chain onto the guide bar with the
cutters facing the same direction (Fig. E2).
7. Replace the side cover onto the chain saw housing
and fully tighten the two lock nuts.
8. Rotate the chain by hand to check whether the chain
is properly assembled without binding. Otherwise,
reassemble the chain and bar.
NOTICE:
To extend the guide bar life, invert the bar
occasionally.
ADJUSTING THE CHAIN TENSION
◾
Stop the motor and remove the battery pack before
adjusting the chain tension. Turn the chain-tensioning
bolt clockwise or counterclockwise to adjust chain
tension (Fig. F) until the chain seats snugly against the
guide bar with the drive links in the guide bar groove.
◾
A cold chain is correctly tensioned when there is no
slack on the underside of the guide bar and the chain
is snug, but it can be turned by hand without binding.
The chain must be re-tensioned whenever the flats on
the drive links do not sit in the bar groove.
◾
During normal saw operation, the temperature the
chain will increase. The drive links of a correctly
tensioned warm chain will hang approximately 1.3 mm
out of the bar groove (Fig. G).
NOTICE:
New chains tend to stretch; check chain tension
frequently and tension as required.
NOTICE:
A chain tensioned while it is warm may be too
tight upon cooling. Check the cold tension before next use.
OPERATION
WARNING:
Do not allow familiarity with this product
to make you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
WARNING:
Do not use any attachments or
accessories not recommended by the manufacturer of
this product. The use of attachments or accessories not
recommended can result in serious personal injury.
Guide Bar Groove
WARNING:
cause serious personal injury, always remove the battery
Drive Sprocket
pack from the tool when assembling parts, making
adjustments, cleaning, or when not in use.
Before each use, inspect the entire product for damaged,
missing, or loose parts, such as screws, nuts, bolts, caps,
etc. Securely tighten all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced.
APPLICATION
You may use this product for basic felling, limbing, pruning,
and woodcutting of lumber and trees.
NOTICE:
purposes. Any other use is deemed to be a case of misuse.
FILLING BAR AND CHAIN LUBRICANT
WARNING:
near the oil or the chain saw. Oil may spill and cause a
fire.
NOTICE:
purchase. It is essential to fill the tank with oil before use.
The chain is automatically lubricated with chain oil during
operation.
1. Position the chain saw on its side with the tank cap
facing upwards.
2. Clean the oil tank cap and the area around it to ensure
that no dirt falls into the oil tank.
3. Lift up the semicircular plate and rotate the oil tank
cap counterclockwise to remove it (Fig. H).
4. Carefully pour the bar and chain oil into the tank. Fill to
the bottom of the fill neck.
5. Wipe off any excessive oil and replace the cap.
NOTICE:
level falls below the minimum line. Never operate the chain
saw if the oil is not visible.
ATTACHING/DETACHING THE BATTERY PACK
Use only with EGO's battery packs and chargers listed
in Fig. A2.
Fully charge before first use.
To Attach
Align the battery ribs with the mounting slots and press the
battery pack down until you hear a "click" (Fig. I).
To Detach
Depress the battery-release button and pull the battery pack
out (Fig. J).
56 VOLT LITHIUM-ION CORDLESS CHAIN SAW — CS2000E
To prevent accidental starting that could
The machine is to be used only for its prescribed
Do not smoke or bring any fire or flame
The chain saw is not filled with oil at the time of
Check the oil level frequently and fill when the oil
EN
9