Ego Power+ PAD5000E Manual página 8

OVER TEMPERATURE PROTECTION
EN
If the battery or inverter temperature exceeds 70°C
during operation, the temperature-protection circuit will
shut off the unit in 1 minute to protect from overheating
damage. The power button indicator will glow solid red
for 1 minute. Allow the unit to cool until its temperature
drops below 67°C before restarting.
LOW BATTERY PACK CHARGE PROTECTION
The inverter automatically shuts down 1 minute after the
battery pack charge reached a low level.
Charge the battery pack.
OVERLOAD OR SHORT CIRCUIT PROTECTION
When the connected AC device draws more than the
rated power of the port, the inverter LED indicator will
flash red for 1 minute at 1 flash every 0.5 seconds. Then
the inverter will automatically shut down.
Disconnect the AC device.
USING WITH EXTERNAL DEVICES
To power devices
When a charged battery pack is installed, the power in-
verter converts DC electricity to 220-240V AC household
power and/or USB-A (5/9/12V, up to 18 W) or USB-C
output port 1 (5/9/12/15/20V, up to 18 W) or USB-C
input/output port 2 (5/9/12/15/20V, up to 100 W) supply
power, allowing the user to charge and power a variety
of devices.
NOTE:
When switching on the power inverter, if the USB
output current is less than 100mA and the AC output
power is less than 10W, the system will shut off automat-
ically in 2 hours.
To charge battery pack
The power inverter can charge the EGO battery when a
USB-PD compatible charger is connected to the USB-C
input/output port 2 (5/9/12/15/20V, up to 100 W).
NOTE:
◾
When incompatible charger is connected and the other
ports are not connected to power devices, EGO battery
will be charged by 5V1A or not be charged, and after
30 min, the inverter will turn off automatically.
◾
When incompatible charger is connected and the other
ports are connected to power devices, EGO battery will
not be charged and after 30 min, the inverter will stop
the charging with power button LED indicator only
shows the indication of powering devices.
8
56 VOLT POWER INVERTER — PAD5000E
To connect external devices:
1. Insert a battery pack into the power inverter.
2. Press and hold the power button for more than a
second to turn the inverter ON. The LED in the power
button will illuminate green when the inverter is
ready to use.
3. Connect devices into the power inverter's USB ports
and/or 220-240V (230V of center voltage) AC output
port. The inverter will begin powering the devices
automatically.
4. Connect compatible USB PD charger into the
inverter's USB-C input/output port 2 to charge the
EGO battery installed on the inverter.
5. When the power inverter is not in use, disconnect the
devices from the inverter, then press and hold the
power button for more than a second to turn it OFF.
6. Remove the battery pack from the power inverter.
NOTE:
◾
Runtime of the connected device is dependent upon
the device and the EGO battery capacity.
◾
Charging time of the EGO battery pack is dependent
upon the USB PD charger.
◾
The power inverter may get warm. This is part of the
normal operation of the power inverter.
◾
Always use the power inverter in a well-ventilated area.
◾
Do not insert a nail, wire, etc. into the USB ports.
Otherwise a short circuit may damage the USB ports.
◾
When a power bank is connected, sometimes the
GREEN LED of the power button fades in and out, that
means "powering the power bank". Sometimes the
ORANGE LED fades in and out, that means "charging
the EGO battery pack".
MAINTENANCE
WARNING:
To avoid serious personal injury, always
disconnect all devices and remove the battery pack from
the power inverter when cleaning or performing any
maintenance.
WARNING:
When servicing, use only identical EGO
replacement parts. Use of any other parts may create a
hazard or cause product damage. To ensure safety and
reliability, all repairs should be performed by a qualified
service technician.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use a clean cloth to remove dirt, dust, oil, grease, etc.