Publicidad
Idiomas disponibles
Idiomas disponibles
Wear eye protection.
n
Visible radiation. Do not stare into light.
Date Code Position (Fig. A)
14
The date code
, which also includes the year of manufacture,
is printed into the housing.
Example:
2022 XX XX
Year of Manufacture
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
1
Battery
2
Battery release button
3
Main handle
4
Top handle
5
Side handle
6
Speed selector knob
7
Trigger switch
Intended Use
The DCD470 right angle drill is designed for professional drilling
at various work sites (i.e., construction sites)
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
These heavy-duty right angle drills are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
•
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Torque
WARNING: This is a high-torque drill. To reduce the risk of
serious personal injury, ALWAYS hold tool firmly with both
hands in the proper position for operation as shown.
Torque is the twisting action the drill produces in regards to
the rotating bit. As the drill bit meets resistance in the material
being drilled, the motor responds by adjusting the output
torque to meet the requirement up to the maximum capacity of
the motor and gear system.
Bracing the Tool (Fig. C, H)
WARNING: To reduce the risk of serious personal injury,
ALWAYS hold or brace the tool securely in anticipation of
a sudden reaction.
8
Worklight
9
Forward/reverse button
10
13 mm keyed chuck
11
Chuck key
12
E-Clutch® indicator
13
D
WALT Tool Tag
e
mounting holes
WARNING: To reduce the risk of serious personal injury,
NEVER brace the tool against the battery pack.
With hands in the proper hand position (also refer to Fig. H),
brace the tool as shown in Figure C.
The bit rotates clockwise when the tool is in the forward
position and counterclockwise when the tool is in the reverse
position. Using proper hand position, brace the side handle
or tool body against a stud for better support (Fig. C).
Clutch
The DCD470 is equipped with a mechanical slip clutch. The
clutch is active when the low speed (1) is selected. When the
bit or cutter bites into the workpiece, the clutch will slip and a
ratcheting sound will be heard. Release the trigger. Continued
clutching of the tool will reduce the life of this feature.
E-Clutch® System (Fig. A)
The DCD470 is equipped with the D
E-Clutch® system. This feature senses the motion of the tool
and shuts the tool down if necessary. The red LED indicator
illuminates when the E-Clutch® system is engaged.
InDICaTOR DIaGnOsIs
OFF
Tool is functioning
normally
SOLID
E-Clutch® System
has been activated
(ENGAGED)
Top Handle (Fig. D)
4
A fixed top handle
is provided for carrying the tool and for
use as an additional handle.
Side Handle (Fig. E)
WARNING: To reduce the risk of personal injury, always
operate the tool with the side handle properly installed
and tightened. Failure to do so may result in the side
handle slipping during tool operation and subsequent loss
of control. Hold tool with both hands to maximize control.
The two position side handle
side of tool. Thread the side handle
15
holes
on desired side. Tighten securely by hand.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
WARNING: Use only D
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
EnGLIsh
WALT anti-rotation
e
sOLUTIOn
Follow all warnings and instructions
when operating the tool.
With the tool properly supported,
release trigger. The tool will function
normally when the trigger is
depressed again and the indicator
light will go out
5
can be assembled into either
5
directly into threaded
WALT battery packs and chargers.
e
1
is fully charged.
5
12
35
Publicidad
