Publicidad
Idiomas disponibles
Idiomas disponibles
© Lens connector (4 pin socket)
Supplies power and control signals to an auto iris lens.
O Auto iris lens selection switch (DC/VIDEO)
Switch for selecting the control signal for the auto iris lens.
DC:
For auto iris lenses controlled by DC signals
VIDEO:
For auto iris lenses controlled by video signals
* When the DC/VIDEO switch is set to VIDEO, the backlight compensation
function may not work properly.
« When the DC/VIDEO switch is set to VIDEO, "hunting" may occur. If this
occurs, use the LEVEL L/H adjustment screw on the lens to change the
incident light level. When adjusting the incident light level, set the ALC
(Automatic Light Control) adjustment screw to Av.
© Camera mounting bracket
The mounting bracket can be attached to either the top or bottom of the
camera using the four attached screws (1/4" UNC-20). On the SSC-DC330/
334, the camera mounting bracket is attached on top of the main body. On
the SSC-DC330P/334P/338P,
it is attached underneath the main body.
Rear
Ei
© SYNC switch (SSC-DC334/334P/338P)
Use this switch to set the camera synchronization mode—line lock (L.L) or
internal (INT).
@ AGC (automatic gain control) ON/OFF switch
The automatic gain function automatically adjusts picture gain in accordance
with the brightness of the subject.
© Gain up switch
Switching the Gain up switch to the TURBO mode while the AGC switch @
is on increases gain by up to 6dB over the NORM (normal) mode.
© BLC (back lighting compensation) ON/OFF switch
When switched on, this function adjusts exposure to compensate for
situations where the subject is lit from behind.
@ CCD-IRIS ON/OFF switch
When using a manual iris lens, the CCD-IRIS function automatically adjusts
the shutter speed to maintain a suitable exposure level.
@® White balance mode switch
When set in the ATW (auto tracing white balance) - PRO position, the
camera automatically adjusts white balance to suit the color temperature of
various lighting sources, including incandescent, fluorescent and natural
lighting.
When set to the ATW position, the camera automatically adjusts white
balance to suit special lighting sources such as sodium lamps.
@ Aperture switch
Set in the "SHARP" mode to sharpen the outline and produce a clearer
picture.
® DC 12V power supply (SSC-DC330/330P)
Use this switch to turn the power supply on and off. When using a DC 12 V
power supply, set this switch to ON. This switch does not function when
using YS-W150/150P/250/250P camera adapter (not supplied).
@® Mode change switch (SSC-DC330/330P)
Power source changes as follows.
Power source
YS-W150/150P/
250/250P
DC 12 V
Connector ®
MONITOR OUT
VS IN
Connector ®
DC IN/VS IN/
VIDEO OUT
VIDEO OUT
® DC IN (power input)/VS IN (external synchronization signal input)/VIDEO
OUT (composite video signal output) or VIDEO OUT connector (BNC
type) (SSC-DC330/330P)
@ MONITOR OUT or VS IN (external synchronization signal input)
connector (BNC type) (SSC-DC330/330P)
The functions of these connectors (8 and @) are changed by the mode
change switch @.
@ VIDEO OUT connector (BNC-type) (SSC-DC334/334P/338P)
® Ground terminal (screw type) (SSC-DC334/334P)
@® DC 12 V screw terminals (SSC-DC330/330P)
Connect to an external power supply of DC 12 V.
AC 24 V screw terminals (SSC-DC334/334P)
Connect to an external power supply of AC 24 V.
@ Power cable (SSC-DC338P)
Connect to an AC power supply of 220 V to 240 V.
@ H-PHASE adjustment screw (SSC-DC330/330P)
Use to adjust the horizontal phase of cameras synchronized by VS lock.
@® V-PHASE adjustment screw (SSC-DC334/334P/338P)
Use to adjust the vertical phase of cameras synchronized by Line lock.
® VIDEO LEVEL adjustment screw
Use to adjust the video level when using a DC servo lens.
Publicidad
