Descargar Imprimir esta página

EINHELL GE-CT 18/33 Li E Manual De Instrucciones Original página 22

Recortadora de césped de batería

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 99
5.8 Charging the battery (Fig. 13)
1. Take the battery pack out of the equipment.
Do this by pressing the side pushlock buttons.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the mains socket outlet. The green LED
will then begin to fl ash.
3. Insert the battery pack into the battery char-
ger.
4. In section „Charger indicator" you will fi nd a
table with an explanation of the LED indicator
on the charger.
The battery pack can become a little warm during
the charging. This is normal. If the battery pack
fails to charge, check:
whether there is voltage at the socket outlet
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
the charging unit
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.9 Battery capacity indicator (Fig. 14)
Press the switch for the battery capacity indicator
(Item B). The battery capacity indicator (Item A)
shows the charge status of the battery using 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
Anl_GE_CT_18_33_Li_E_SPK13.indb 22
Anl_GE_CT_18_33_Li_E_SPK13.indb 22
GB
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
Please note that the statutory regulations gover-
ning noise abatement may diff er from one loca-
tion to another.
Danger! The guard hood must be fi tted when
carrying out work.
6.1 Switching the equipment on and off ,
adjusting the speed
6.1.1 Adjusting the speed (Fig. 12)
Warning! Set the speed only when the motor is
at a standstill.
Push the switch (Item 13) into position "1" =>
Low speed, longer battery running time. Push the
switch (Item 13) into position "2" => High speed,
shorter battery running time.
6.1.2 Switching on
Press the left or the right safety lock-off (Item 4)
and the On/Off switch (Item 3). Once the tool is
running, you can release the safety lock-off .
6.1.3 Switching off
Release the On/Off switch.
6.2 Practical tips
Practice all the work steps with the motor swit-
ched off and without the rechargeable battery
before you start to use the equipment. Only ever
cut grass that is dry. If the grass is long, the grass
must be cut shorter in stages (Fig. 15).
Extending the cutting line (Fig. 16)
Danger! Do not use any kind of metal wire or me-
tal wire encased in plastic in the line spool. This
may cause serious injuries to the user.
- 22 -
01.06.2023 10:19:22
01.06.2023 10:19:22

Publicidad

loading

Este manual también es adecuado para:

34.112.70