Publicidad
Preparing the machine for work
Before starting work, wear overalls, ear protectors, non-slip waterproof shoes, mask to protect the re-
spiratory tract, gloves and all other personal protection devices recommended by the supplier of the
Before starting work, proceed as follows:
►
Battery models: check the battery charge (charge if necessary);
►
make sure the dirty water tank (fig. A, ref. 2) is empty. If necessary, empty it;
►
via the opening at the front, fill the detergent tank (fig. A, ref. 8) with a suitable concentration of clean
water and low-foam detergent. Leave at least 5 cm between the surface of the liquid and the opening of
the tank;
►
mount the most suitable brushes or drive disks for the floor and work to be performed (see paragraph
3.4);
►
make sure that the squeegee (Fig. A, ref. 5) is securely fastened and connected to the suction hose;
check that the rear blade is not worn (standard version with brushes and drive disks).
►
adjust the squeegee working height by turning the knob provided (Fig. E, ref. 14), roller version.
►
adjust the brush roller working height by turning the knob provided (Fig. Q, ref. 1), roller version.
If you are using the machine for the first time, we recommend trying it on a large obstacle-free surface first
Always empty the dirty water tank before filling the detergent tank again.
For effective cleaning and to extend the working life of the machine, follow a few simple rules:
►
prepare the work area by removing all possible obstacles;
►
begin working from the furthermost point to avoid walking on the area you have just cleaned;
►
choose the straightest possible working routes;
►
divide large floors into parallel rectangular sections.
If necessary, finish off by passing a mop or rag rapidly over parts inaccessible to the scrubber drier.
Working
After setting up the machine, proceed as follows.
►
Connect the machine as follows:
►
cable model: plug the machine into the mains power socket;
►
lower the squeegee using the lever provided (Fig. D, ref. 2), standard version with brushes and drive
disks;
►
press the main switch (fig. C, ref. 3) (LED on);
►
press the brush button (fig. C, ref. 4) "LED on", this will also automatically activate suction and solution
flow. To extend machine operating time, the ECO function can be activated (see the paragraph "Con-
trols - Descriptions");
►
select the direction of movement by pressing the button (fig. D, ref. 4) (models with electric drive)
►
adjust the forward/reverse speed by turning the potentiometer (fig D, ref. 5) (models with electric drive)
►
press the brush lever (fig. D, ref. 1);
►
check regularly that detergent is reaching the brushes and top up if necessary;
►
while working, check the quality of washing and adjust the flow of detergent to the brushes using the
detergent tap (fig. G, ref. 2), in the ECS model, the detergent tap must always be fully open.
Empty the dirty water tank each time you fill the detergent tank.
►
The float switch in the dirty water tank (fig. I, ref. 1) turns suction off when the tank is full. If the switch
trips, stop work and empty the tank;
►
Battery models: if the red LED (fig. C, ref. 2) starts flashing, the batteries are nearly flat. After a few
seconds, the brush and suction motor shut down to prevent draining the batteries excessively. Charge
the batteries.
►
ECS model: during cleaning, make sure the pressure of the microfibre on the work surface remains
within the permitted range. If the light in the brush button starts flashing while you are working, reduce
the pressure of the microfibre by turning the knob (fig. O, ref. 1). Turn the knob clockwise to reduce the
pressure of the microfibre on the work surface; turn the knob anticlockwise to increase the pressure of
the microfibre on the work surface. To access the knob, raise the dirty water tank.
detergent used or necessitated by the work environment.
i INFORMATION
to acquire the necessary familiarity.
IMPORTANT
IMPORTANT
GB
28
Publicidad
