Publicidad
Idiomas disponibles
Idiomas disponibles
· TRANSLATION OF THE ORIGINAL · ENGLISH
EN
Cut the material to the desired width using the instructions
for the straight cut.
2.
Adjust the fence to the desired width, and secure
it in place.
3.
Position the material on the table firmly against the
fence.
4.
Ensure that the material does not touch the cutting
blade before turning on the saw.
5.
Turn the on/off switch to the ON position.
6.
Allow the cutting blade to reach its maximum speed
and wait for it to become wet before moving the
material towards the blade.
7.
Hold the material firmly against the fence and move
the material to be cut towards the cutting blade.
8.
Cut the material sufficiently but not excessively.
9.
Turn the on/off switch to the OFF position.
10.
Turn the material over to cut along the length of
the other mark. This time go over the other line and
the cut piece should separate from the rest of the
material.
11.
After making the cut, switch off the saw. Wait for the
cutting blade to stop completely before removing
any part of the material.
TO MAKE A MITER CUT (Figure 17,18)
Miter cuts of 22.5° and 45° can be made using the tilting
table.
NOTE: Miter cuts must be done with the tile upside
down.
1.
Raise the tilting table.
2.
At the bottom of the tilting table, lower the two
table legs at right angles to the plate.
3.
Use the first slots on the legs to rest the plate at an
angle of 22.5°.
Use the second set of slots to incline the table at a
greater angle of 45°.
NOTE: Ensure that the tilting table is firmly secured in its
position before starting to cut.
4.
Turn the on/off switch to the ON position.
5.
Allow the cutting blade to reach its maximum speed
and wait for it to become wet before moving the
material towards the blade.
6.
Hold the material upside down firmly against the
tilting table and move the material towards the
cutting blade.
7.
After making the cut, switch off the saw. Wait for the
cutting blade to stop completely before removing
any part of the material.
7.- MAINTENANCE OF THE SAW
WARNING: When carrying out maintenance use only
identical spare parts. Use of any other part can create a
hazard or cause damage to the product.
- 8 -
Español
English
7.1 Cleaning the saw
It is important to clean the saw frequently.
During use, the fence and the angle guide will get dirty and
prevent the guide from sliding smoothly.
Unplug before performing any adjustments, repairs or
maintenance.
Do not use aggressive cleaning products to clean the
machine.
Do not submerge the machine in water.
•
Remove the guides and the tilting table from the
saw.
•
With a small brush and water, thoroughly clean
each part to remove any trapped residue.
•
Remove the drain plug and empty the dirty water
in a bucket.
•
Rinse the machine properly.
•
Dispose of the waste water in accordance with local
regulations.
•
Replace the drain plug.
•
Dry the saw.
Do not use solvents to clean plastic parts.
7.2 After-sales service
Use only original spare parts supplied by the manufacturer.
Repairs should only be done by certified workshops or
RUBI's technical service:
RUBI TOOLS USA Inc.
3980 West 104th Street,
Suite 6
Hialeah, FLorida (33018)
+1 305-715-9892
+1 305-715-9898
+34 682 16 90 55
rubitools.usa@rubi.com
8.- GUARANTEE
The guarantee covers all manufacturing or assembly
defects in accordance with the legislation in force. The
guarantee does not cover malfunctions cause by improper
use, overloads, failure to follow the operating instructions
and normal wear and tear. Handling by personnel other
than our Official Service shall void the guarantee. The
proof of purchase must be included with this document
for any claims.
For more details and information, consult the general
guarantee conditions at: www.rubi.com
9.- CETIFICATE
CONFORMS TO
UL STD 987
CERTIFIED TO
CSA STD C22.2 NO. 71.2:2010
5012917
Publicidad
