Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
The dimensions of the following kitchen hoods are shown in Figure 4.
02862_ Bolero Flux TLM 606500 Inox A
-
Before installing the kitchen hood, make sure that the area is clean to prevent it from
sucking in dust or dirt.
-
Please note that the kitchen hood must not share the same ventilation duct with other
appliances that use gas or other fuses.
-
To facilitate air outlet, the ventilation duct should have a curvature of ≥120° and should be
connected to the outside wall, parallel to or above the starting point.
-
After installation, ensure that the kitchen hood is level to prevent grease build-up on the
end (Fig. 5).
Steps to install the kitchen hood:
1
The kitchen hood should be placed at a distance of 65-75 cm above the cooking surface for
best effect (Fig 6).
Using a drill, drill 4 Ø 5 mm holes and a Ø 170 mm hole at the bottom of the wall unit as
2
shown in Figure 7.
Fig. 7 key:
A. Hole 4 - ø5 mm
B. Hole ø170 mm
C. Washer (gasket) 4 - ø12
D. Screw 4 - M4x30
E. Cabinet
Air outlet
F.
G. Washer 4 -M4
3
Remove the mesh filter. Insert the plastic plugs into the holes and secure the kitchen hood
to the cabinet using the screws. Make sure it is centred with the worktop and replace the
filter.
4
Once the kitchen hood has been hung up, you can install the flexible chimney connection
pipe (Ø150 mm) at the outlet of the ventilation duct, located at the top of the kitchen hood
(Fig. 8). If necessary, connect the other end of the flexible connection pipe to the wall
chimney.
5
Connect the connection cable to the mains socket.
Black cable (or brown, depending on models) > Phase
Blue cable > neutral
Yellow-Green cable > ground
You must connect the phase and neutral cables to a 220-240 V~/ 50 Hz power cable.
The kitchen hood must be connected to an earthed installation.
BOLERO FLUX TLM 603500 WHITE A / BOLERO FLUX TLM 603500 BLACK A/
52
BOLERO FLUX TLM 603500 INOX A/ BOLERO FLUX TLM 606500 INOX A
4. OPERATION
Switches
1. To switch on the kitchen hood, set the switch to position "I" or "II".
2. In the low-power position (I), the motor will operate at low speed.
3. In the high-power position (II), the motor will operate at high speed.
4. To stop the operation of the kitchen hood, turn the switch to the "0" position.
5. To switch on the light, put the switch to "I" position.
6. To switch off the light, put the switch to "0" position.
NOTE: the hoods are equipped with an overheating protection system that acts to prevent
possible incidents when the motor temperature exceeds the operating limit value.
5. CLEANING AND MAINTENANCE
Always switch off the power supply before cleaning or performing any maintenance work on
the kitchen hood. Please note that the cleaning and maintenance frequency depends on the
use frequency and intensity.
1. To prevent the outer surface of the kitchen hood from deteriorating over time, it is
recommended that it be cleaned with hot water and a non-corrosive detergent every two
months.
2. Do not use abrasive detergents. Otherwise, the surface of the kitchen hood may be
damaged.
3. Keep the motor and other parts away from water, as water may damage the appliance.
Cleaning the filters
Do not use corrosive detergents to clean grease from the mesh filters. Regular cleaning of
the filters will prolong the life of the appliance and keep it in good working order. Follow the
instructions below:
-
Cleaning method 1: immerse the mesh filters in hot water (40-50 °C), add neutral detergent
and let them soak for 2 to 3 minutes. Protect yourself with gloves and clean the filters with
a soft brush or scouring pad. Do not apply too much force, as filters are very delicate and
can be easily damaged.
-
Cleaning method 2: if you wish, you can also wash the filters in the dishwasher at a
temperature of approx. 60 °C.
BOLERO FLUX TLM 603500 WHITE A / BOLERO FLUX TLM 603500 BLACK A/
BOLERO FLUX TLM 603500 INOX A/ BOLERO FLUX TLM 606500 INOX A
ENGLISH
53
Publicidad
