Publicidad
Idiomas disponibles
Idiomas disponibles
Solutions
to Common
Problems
Service Prevention Checklist, continued
OCCURRENCE
POSSIBLE CAUSE
SOLUTION
t
Water
collects
in folds of
This is a result of the washing
action
and
is
the bellows
at the end of
part of the normal
operation
of the washer.
the cycle.
Water
collects
in bleach
This is a result of the siphoning
action
and is
Water
may be removed
by removing
the dispenser
drawer
(see Care and Cleaning
and fabric
softener
cam-
part of the normal
operation
of the washer,
inthis guide) and draining
water
into the empty drum or sink.
partments.
Wash
load too wet after
Washer
is overloaded.
Do not overload
washer. Bee Operating
Your Washer.
spin.
Load is too small.
Add 1 or 2 similar items to help balance
the load.
Load isout of balance.
Rearrange
load to allow
proper
spinning.
Drain hose is kinked.
Straighten
drain
hose.
Water
does not enter
Water
supply is not adequate
in area.
Check another faucet in the house. Wait until water supply and pressure increase.
washer or it enters slowly.
Water
supply
faucets
are not completely
Fully open hot and
cold faucets.
open,
Water
is being
used elsewhere
in the house.
Avoid running
water
elsewhere
while
washer is filling.
Water
pressure must be at least ]0 psi (70
kPa).
Water
inlet hoses are kinked,
Straighten
hoses,
Warm
or hot water
is not
Hot water
heater
is set too low or is a distance
Measure
hot water
temperature
at nearby
faucet
with candy
or meat thermom-
hot enough,
from washer,
eter. Water
temperature
should
be at least ]20°F
{49°C).
Adiust water
heater
as necessary.
Hot water
is being
used elsewhere
in the
Avoid using hot water
elsewhere
before
or during
washer
use. There may not be
house,
enough
hot water
available
for
proper
cleaning.
If problem
persists_ your
hot
water
system
may be unable
to support
more than ] use at a time,
Water
in washer
does not
Drain hose is kinked
or clogged.
Clean and
straighten
the drain
hose.
drain or drains
slowly.
Drain hose standpipe
is too tall.
Maximum
Reduce
standpipe
height to less than
56.5"
(144 cm).
See INSTALLATION
standpipe
height
is 56.5" (144 cm).
INSTRUCTIONS,
House drain pipes are clogged,
Unclog
drain pipes.
Contact
plumber
if necessary.
Water
leaks,
Fill hose connection
is loose at faucet
or
Check and tighten
hose connections.
Ensure rubber
sealing
washers are installed.
washer.
Oversudsing.
Wrong
detergent.
Run rinse cycle. Use a Iow-sudsing_
high efficiency
detergent.
Too much detergent.
Run rinse cycle. Use less detergent
in future
loads.
Incorrect
wash and
rinse
Hot and cold
water
hoses are connected
to
Connect
hot water
hose to hot water
faucet
and cold water
hose to cold water
temperatures,
wrong supply
faucets,
faucet.
Water
is entering
washer
Drain hose standpipe
is too
low. Standpipe
Increase standpipe
height to at least 24" (61 cm). See INSTALLATION
INSTRUC-
but tub does not fill.
must be a minimum
of 24" (61 cm) high to
TIONS.
prevent
siphoning.
27
Publicidad
