Milwaukee MXF SC Manual Original página 8

TECHNICAL DATA
Type
Frequency band(s) of Bluetooth
Maximum radio-frequency power transmitted in the frequency
band(s)
Bluetooth version
Output Volts
Quick charge current
Weight according EPTA-Procedure 01/2014
Recommended ambient charging temperature
WARNING
Read all safety warnings, instructions,
illustrations and specifi cations provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY WARNINGS
Do not dispose of used battery packs in the household refuse or by
burning them. Milwaukee Distributors off er to retrieve old batteries to
protect our environment.
Only the following battery packs can be
charged with this charger:
Battery Cell DC Capacity
Cat. No. Type Volts
MXFCP203 Li-Ion 72 V ≤ 3.0 Ah
MXFXC406 Li-Ion 72 V ≤ 6.0 Ah
Do not try to charge non-rechargeable
batteries with this charger.
Do not store the battery pack together with metal objects (short
circuit risk).
No metal parts must be allowed to enter the battery section of the
charger (short circuit risk).
Never break open battery packs or chargers and store only in dry
rooms. Keep dry at all times.
The battery clamps of the charger are fed by mains supply. Do not
touch the tool with conducting objects.
Never charge a damaged battery pack. Replace by a new one.
Before use check machine, cable, and plug for any damages or
material fatigue. Repairs should only be carried out by authorised
Service Agents.
Use only System MXF chargers for charging System MXF battery
packs. Do not use battery packs from other systems.
This appliance is not intended to
be used or cleaned by persons with
reduced physical, sensory or mental
capabilities, or lack of experience or
knowledge, unless they have been
given instructions concerning the
safe use of the appliance by a person
legally responsible for their safety. They
should be supervised whilst using the
appliance. Children shall not use, clean
or play with this appliance, which when
14
MXF SC
Battery Charger
2402-2480 MHz
3 dBm
BLE V4.2
72 V
12 A
8,8 kg
+5...+40 °C
not in use should be secured out of
their reach.
WARNING This device contains a lithium button/coin cell
battery. A new or used battery can cause severe internal
burns and lead to death in as little as 2 hours if swallowed or
enters the body. Always secure the battery cover. If it does not close
securely, stop using the device, remove the batteries, and keep it
away from children. If you think batteries may have been swallowed
or entered the body, seek immediate medical attention.
Warning! To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery pack
or charger in fl uid or allow a fl uid to fl ow inside them. Corrosive or
conductive fl uids, such as seawater, certain industrial chemicals,
and bleach or bleach containing products, etc., can cause a short
Cell
circuit.
No.
SPECIFIED CONDITIONS OF USE
20
This charger charges MXFCP203 and MXFXC406 Milwaukee Li-Ion
battery packs.
2 x 20
Do not use this product in any other way as stated for normal use.
MAINS CONNECTION
Connect only to a single-phase AC current supply and only to the
mains voltage specifi ed on the rating plate. Must only be used from
sockets with earth wire.
CHARGING TIME
Battery Cat. No. Volts Capacity
MXFCP203 72 V ≤ 3.0 Ah
MXFXC406 72 V ≤ 6.0 Ah
NOTES FOR LI-ION BATTERIES
Use of Li-Ion batteries
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of
the battery pack. Avoid extended exposure to heat or sunshine (risk
of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged,
after used.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and
away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
Battery protection for Li-Ion batteries
In extremely high torque, binding, stalling and short circuit situations
that cause high current draw, the tool will stop for about 2 seconds
and then the tool will turn OFF. To reset, release the trigger. Under
extreme circumstances, the internal temperature of the battery could
ENGLISH
become too high. If this happens, the battery will shut down.
Under extreme circumstances, the internal temperature of the
battery pack could raise too much. If this happens, the fuel gauge
will fl ash until the battery pack cooled down. After the lights go off ,
the work may continue.
Transport of Li-Ion batteries
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated
to prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
CHARACTERISTICS
After inserting the battery into the reception of the charger the
battery will automatically be charged (red control lamp is illuminated
continuously)
A fully discharged battery pack with an internal tem-perature in the
normal range will charge in about 35 to 75 minutes, depending on
the battery pack and internal temperature of the charger.
Heavily cycled batteries may take longer to charge completely.
The fuel gauge lights are displayed as the pack is be-ing charged,
indicating how fully charged the pack is. The fuel gauge will turn off
when charging is complete.
Once the battery is fully charged, the LED on the charger changes
from red to green and the LEDs on the battery go out.
If the light indicator fl ashes red and green or does not come on,
check that the battery pack is fully seated into the bay. Remove
Charging Time
the battery pack and reinsert. If the light continues to fl ash red and
approx.
green or does not come on, remove pack(s) and unplug charger for
at least 2 minutes. After 2 minutes, plug charger back in and insert
55 min
pack. If the problem persists, contact a MILWAUKEE service facility.
90 min
CHARGER LIGHT INDICATORS
Continuous red
Slow fl ashing green
Continuous green
Fast fl ashing red
Flashing red/green
WORKING INSTRUCTIONS
New batteries must be charged before fi rst use. The battery is
shipped in sleep mode.
Cold Weather Operation
MILWAUKEE Li-Ion battery packs are designed to operate in
temperatures below freezing. When the battery pack is too cold,
it may need to warm up before normal use. Put the battery on a
product and use the product in a light application.
ONE-KEY™
To learn more about the ONE-KEY functionality for this tool, please
reference the Quick Start guide included with this product or go to
milwaukeetool.com/ One-Key. To download the ONE-KEY app, visit
the App Store or Google Play from your smart device.
Also, when the product experiences ESD, the Bluetooth
communication will be disconnected. It needs to be reset manually
to recover.
ONE-KEY™ Indicator
Solid Blue
Blinking Blue
Blinking Red
MAINTENANCE
If the supply cord of this appliance is
damaged, it must only be replaced
by a repair shop appointed by the
manufacturer, because special purpose
tools are required
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the machine type printed as well as the six-digit No. on
the label and order the drawing at your local service agents or
directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
Charging
Approaching full charge
Charging is complete
Battery or charger is too hot/cold
- charging will begin/resume
when battery or charger reaches
correct charging temperature
Damaged or faulty battery pack
or charger
ENGLISH
Wireless mode is active and ready to be
confi gured via the ONE-KEY™ app.
Tool is actively communicating with the ONE-
KEY™ app.
Tool is in security lockout and can be unlocked
by the owner via the ONE-KEY™ app.
15