Ego Power+ STX4500 Instrucciones Originales página 9

WARNING:
Do not attempt to modify this product or
create accessories not recommended for use with this line
trimmer. Any such alteration or modification is misuse and
could result in a hazardous condition leading to possible
serious personal injury.
WARNING:
To prevent accidental starting that could
cause serious personal injury, always remove the battery
pack from the machine when assembling parts.
WARNING:
When the machine is equipped with
brush cutter head, the safety barrier bar shall be mounted.
MOUNTING THE GUARD (FIG. B1 & B2)
WARNING:
Always wear gloves when mounting or
replacing the guard. Take care of the blade on the guard
and protect your hand from cutting.
WARNING: N
ever operate the machine without
the guard firmly in place. The guard must always be
on the machine to protect the user! When the guard is
fixed, never attempt to remove or adjust the guard, if
a replacement is needed, it should be performed by a
qualified service technician!
NOTICE:
There are two kinds of guards compatible with
this machine. Only the guard with icon
with line trimmer head and must NOT be used with brush
cutter head. Be careful to choose the correct guard when
using the machine.
NOTICE:
The brush cutter guard is sold separately.
Loosen and remove the two bolts from the guard, align
the guard mounting holes with the assembly holes and
then lock the guard onto the shaft base with the two bolts,
together with two spring washers.
WARNING:
Make sure the guard is fixed according
to Fig. B1 & B2, any reverse fixing will cause great danger!
MOUNTING AND ADJUSTING THE LOOP HANDLE
1. Stop the motor and remove the battery pack from the
machine, if installed.
2. Loosen the wing nut to separate the adjustable loop
handle (Fig. C).
NOTICE:
Must install the safety barrier bar onto the loop
handle when the machine is equipped with brush cutter
head.
C-1 Loop handle
C-2 Clamping block
C-3 Wing nut
3. Push the loop handle onto the shaft between the
threshold ring and the warning label (Fig. D1).
4. Insert the clamping block into the handle slot (Fig. D2).
5. Align the recessed part in the barrier bar with the
protruded part on the loop handle, press the barrier
bar onto the loop handle (Fig. D3).
6. Mount the quick-release lever and tighten the wing
nut. Make sure that the loop handle is positioned
upwards and points toward the top of the rear handle
(Fig. D4).
7. Pull the quick-release lever up to move/rotate the loop
handle to a comfortable operating position (Fig. D5).
8. Fold the quick-release lever to secure the loop handle
in place (Fig. D6).
WARNING:
loop handle firmly in place.
can be used
REPLACE THE TRIMMER HEAD WITH THE BRUSH
CUTTER HEAD
1. Remove the battery pack from the machine
2. Rotate the trimmer head to align the slot in the flange
with the shaft-locking hole in the gear case and insert
a stabilizer into the hole (Fig. E1).
3. Rotate the trimmer head CLOCKWISE to remove it from
the motor shaft (Fig. E1, E2).
4. The blade is shipped with a sheath. Before mounting
the blade onto the brush cutter, the sheath should be
removed from the hook on the sheath (Fig. E3).
NOTICE:
To protect against injury, you have to wear
gloves prior to any operation with the 3-tooth blade.
5. Mount the inner flange and flange cover into its place,
if they had separated from the shaft (Fig. E4).
6. Mount the blade onto the motor shaft, ensuring that
the surface of the blade is flush with the surface of the
inner flange bulge. Mount the outer flange and the nut
(Fig. E5). Finger-tighten the nut COUNTERCLOCKWISE.
7. Position the gear case against a solid surface for
support. With one hand hold the brush cutter shaft and
the other hand grasp a 16 mm socket wrench (not
included) to tighten the nut COUNTERCLOCKWISE
(Fig. E6).
56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — STX4500
C-4 Quick-release Lever
Safety barrier bar (only
C-5 for use with brush cutter
head)
Never operate the machine without the
EN
9