Blackstone 6303 Manual De Instrucciones página 10

OWNER'S MANUAL | USING YOUR BLACKSTONE
NATURAl GAS ReQUIReMeNTS
• The fixed fuel piping system must use a rigid pipe, semi-riged
tubing and/or a connector that complies with the Standard for
Connectors for outdoor Gas Appliances and Manufactured Homes,
ANSI Z21�75 • CSA 6�27�
• This appliance has been designed and built to utilize natural gas
only� do NoT attempt to operate this appliance using gases other
than natural gas at the indicated pressure�
• This appliance has been provided with a hose that must be used
for proper function� do NoT replace the hose� If the hose becomes
worn or damaged, contact customer support for a replacement�
CONNECTING TO THE NATURAL GAS SUPPLY
Use an adjustable wrench to attach the natural gas hose
STEP 01
swivel fitting to the appliance�
• • do NoT do NoT route the gas supply hose route the gas supply hose
directly underneath the appliance. directly underneath the appliance.
do NoT do NoT route the hose underneath route the hose underneath
or through permanent structures. or through permanent structures.
• • The hose should be checked for The hose should be checked for
cracks, cuts and wear each time cracks, cuts and wear each time
you cook. you cook.
If your natural gas supply line is not already set up with the
STEP 02
correct size Quick Connect/disconnect fitting, the correct one is
included�
Note: Use thread sealant if attaching the provided Quick Connect/disconnect Note: Use thread sealant if attaching the provided Quick Connect/disconnect
fitting. Thread sealant should be rated to 400° F (204°C) and be compatible with fitting. Thread sealant should be rated to 400° F (204°C) and be compatible with
natural gas. (Permatex #59214 or loctite 592) natural gas. (Permatex #59214 or loctite 592)
Note: To have the proper fitting added to your natural gas source, have this Note: To have the proper fitting added to your natural gas source, have this
done by a licensed and insured professional. done by a licensed and insured professional.
Thread reducer Thread reducer
(if required) (if required)
3�8" Quick Connect fitting 3�8" Quick Connect fitting
(included) (included)
DISCONNECTING FROM THE NATURAL GAS SUPPLY
To disconnect your appliance for cleaning or storage, be sure
STEP 01
all of the control knobs are in the oFF position and the natural gas
supply at the Quick Connect valve is oFF�
❶ ❶ Pull the locking collar back and remove the natural
STEP 02
gas hose and release the locking collar� ❷ ❷ Pull apart the hose
and fitting�
Reinstall the dust covers on the supply line as well as the
STEP 03
natural gas hose on the appliance�
10
Swivel fitting Swivel fitting
NG supply NG supply
(from house) (from house)
Shutoff valve Shutoff valve
7" 7"
OFF
water column water column
Connect your appliance to the natural gas supply from the
STEP 03
source by removing the dust covers and making sure both fittings
are free from any debris� ❶ ❶ Pull the locking collar back on the fitting
and ❷ ❷ push the male Quick Connect fitting all the way inside and
then release the locking collar�
❷ ❷
Male Quick Male Quick
Connect fitting Connect fitting
locking collar locking collar
Pull the hose and fitting in opposite directions to verify they are
connected�
Turn on the natural
STEP 04
gas supply�
Prior to turning on your appli-
ance, perform a leak test�
• Use a clean paintbrush to brush a 10�90 mild soap and water solution
onto all the hose connections that you have completed�
• Bubbles will appear in the soapy water if any leaks are present�
• If you have any leaks, turn off your natural gas supply immediately
and fix any leaks before use�
Note: If you are unable to fix the leaks, call a qualified professional who is Note: If you are unable to fix the leaks, call a qualified professional who is
licensed and insured. licensed and insured.
NATURAL GAS ENCLOSURE
CONSTRUCTION
A: A: 4x6 in (10x15 cm) vents at top, and 4x6 in (10x15 cm) vents at top, and
both sides of cabinet. both sides of cabinet.
❶ ❶
❷ ❷
Model: 6303
OFF
❶ ❶
OFF
A A
A A
OFF
BLACKSTONEPRODUCTS.COM/SUPPORT