Publicidad
Idiomas disponibles
Idiomas disponibles
3. Cut slowly and keep the product tilted forwards by ap-
prox. 30° when cutting.
4. Cut long grass in layers from top to bottom.
10.2
Lawn edge trimming (Fig. 3)
The lawn trimmer can be converted as follows to cut the
edges of lawns and flower beds:
1. Set the cutting angle as described under Adjusting the
cutting angle (Fig. 6).
2. Attach the spacer roller (11) to the motor head (15).
It engages audibly.
3. In this way, the lawn trimmer has been converted into
an edge cutter that can be used to make vertical cuts
to the lawn.
4. When edging, guide the product on the edging wheel.
5. In order to change the tool back again, proceed in re-
verse order.
To trim lawn edges, guide the product slowly along the
edges of the lawn.
11 Cleaning and maintenance
WARNING
Have maintenance and repair tasks that are
not described in this operating manual, car-
ried out by a specialist workshop. Use only
original spare parts.
There is a risk of accident! Always perform
maintenance and cleaning work with the bat-
tery removed. There is a danger of injury! Let
the Product cool down before all mainte-
nance and cleaning tasks. Elements of the
engine are hot. There is a danger of injury
and burning!
The product can start unexpectedly and cause injuries.
–
Remove the battery.
–
Allow the product to cool down.
–
Remove the tool attachment.
WARNING
Danger of injury when handling the saw
chain or the blade!
–
Wear cut-resistant gloves.
11.1
Cleaning
1. Never immerse the product in water or other liquids
for cleaning.
2. Do not splash the product with water.
3. Keep protective devices, air vents and the motor
housing as free of dust and dirt as possible. Rub the
product clean with a clean cloth or blow it off with
compressed air at low pressure. We recommend that
you clean the product directly after every use.
4. Ventilation openings must always be free.
5. Do not use any cleaning products or solvents; they
could attack the plastic parts of the product. Make
sure that no water can penetrate the product interior.
11.2
Maintenance
1. Check the product for obvious defects such as loose,
worn or damaged parts before each use.
2. Check the covers and protective devices for damage
and correct seating. Replace them if necessary.
3. You can smooth out slight nicks on the cutting teeth
yourself. To do this, draw an oil stone along the cut-
ting edges. Only sharp cutting teeth provide a good
cutting performance.
11.2.1
1. Open the coil capsule (6) by simultaneously pressing
the two release buttons (6a) on the coil capsule (6).
2. Remove the screws from the coil capsule (6) and take
off the thread coil (16).
3. Pull the thread end of the thread coil (16) out of the
thread outlet eyelet (18).
4. Loosen the Allen screw with a 5 mm Allen key (not
necessarily included in the scope of delivery).
5. Replace the coil capsule (6) and fit it with the Allen
screw.
6. Insert the thread coil (16). Proceed as described un-
der Replacing the thread coil (16) (Fig. 1, 7).
12 Transport and storage
12.1
Transporting the product
1. Attach the spacer roller (11) to the protective cover
(12).
You will hear it click into place.
2. Tilt the product backwards.
3. You can move the product using the spacer roller
(11).
12.2
Preparation for storage
1. Remove the battery.
2. Clean and check the product for damage.
3. For transport or when storing the product, cover the
blade with the blade guard.
4. Fertiliser and other garden chemicals contain sub-
stances that can have a severely corrosive effect on
the metal parts. Do not store the product in the vicinity
of these substances.
Store the product and its accessories in a dark, dry and
frost-free place that is inaccessible to children.
The optimum storage temperature is between 5°C and
30˚C.
Store the product in its original packaging.
Cover the product to protect it from dust or moisture.
Store the operating manual with the product.
13 Repair & ordering spare parts
With this product, it is necessary to note that the following
parts are subject to natural or usage-related wear, or that
the following parts are required as consumables.
www.scheppach.com
Replacing the coil capsule (6)
(Fig. 1, 7)
GB | 21
Publicidad
