Publicidad
Idiomas disponibles
Idiomas disponibles
C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET
Plate position-beneath flat bottom cabinet
Draw a vertical line on the wall at the center of the 30" wide space.
Tape the Rear Wall Template onto the wall matching the centerline and touching the
bottom of the cabinet.
Plate position-beneath recessed bottom cabinet with front overhang
Plate position-beneath framed recessed cabinet bottom
Draw a vertical line on the wall at the center of the 30" space.
Tape the Rear Wall Template onto the wall matching the centerline and touching the
bottom cabinet frame.
At least 30
NOTE
: IT IS
READ
VERY
IMPO RTAN
IN THE
AND FOLL
INSTA
OW THE
T TO
BEFO
RE PROC
LLAT ION
DIRE CTIO
REAR
WALL
EEDIN
INSTR
UCTIO
NS
This Rear
TEMP
G WITH
NS
mountin
Wall Templa
LATE .
THIS
3/8" TO EDGE
g plate
te serves
12"
outlet.
and to
locate
the horizon
to position
the bottom
1. Use
a level
tal exhaust
accurat
ely.
to check
that the
2. Locate
and mark
templat
e is position
right side
of the centerlin
at least
one stud
ed
I t is importa
e.
on the
4"
screw mounte
nt to use
left or
of the microwa
d firmly
in a stud
at least
one wood
location
s for the
ve. Mark
to support
3. Drill
holes in
supplied
two addition
al, evenly
the weight
a stud,
the marked
toggle
bolts.
spaced
Trim the
that do
drill a 3/16"
location
s. Where
rear wall
toggle
not line
up with
hole for
wood screws.
there is
temp late
bolts.
a stud,
drill 5/8"
For holes
along
AT THIS
D O NOT
holes for
the dotte
4. Remove
TIME.
INSTAL
L THE
d line.
5. Review
the templat
MOUNT
ING PLATE
the Installat
e from
the rear
installat
ion situation
ion Instruct
wall.
.
ion book
for your
Darle vuelta
versión
a la hoja
en Españo
para consul
l.
tar la
Locat e
and mark
moun ting
holes to
IMPO RTAN
plate.
align with
T:
holes in
the
LOCA
TE AT
THE CENT
LEAS T
ERLIN
ONE STUD
MARK
E.
ON EITHE
SPAC
THE LOCA
R SIDE
ED TOGG
TION FOR
OF
AREA
LE BOLT
2 ADDI
TION AL,
.
S IN THE
EVEN
MOUN
TING PLAT
LY
E
Trim the
rear wall
temp late
along
the dotte
d line.
Locat e
and mark
moun ting
holes to
plate.
align with
IMPO RTAN
holes in
LOCA
T:
the
TE AT
LEAS T
THE CENT
ONE STUD
MARK
ERLIN
E.
ON EITHE
THE LOCA
R SIDE
SPAC
ED TOGG
TION FOR
OF
AREA
LE BOLT
2 ADDI
.
S IN THE
TION AL,
MOUN
EVEN
LY
TING PLAT
Draw a line on the
back wall equal to
the depth of the front
overhang.
READ
NOTE:
IT IS VERY
IN THE
INSTALLA
AND FOLLOW
IMPORTA
THE DIRECTIO
NT TO
BEFORE
REAR
PROCEED
TION INSTRUCT
NS
This Rear
WALL
TEMPLAT
ING WITH
THIS
IONS
3/8" TO EDGE
mounting
outlet.
Wall Template
plate and
to locate
serves
E.
to position
12"
1. Use
accurately.
a level
to check
the horizontal
exhaust
the bottom
right side
2. Locate
and mark
that the
template
is positioned
It is important
of the centerline.
at least
one stud
on the
left or
4"
of the microwave.
screw mounted
firmly in
to use
a stud
at least
one wood
3. Drill
locations
holes in
for the
supplied
Mark two
additional,
to support
the weight
a stud,
that do
drill a 3/16"
the marked
toggle
locations.
bolts.
evenly
spaced
Trim the
rear wall
toggle
bolts.
not line
up with
a stud,
hole for
wood screws.
drill 5/8"
Where
For holes
there is
template
along
AT THIS
TIME.
DO NOT
INSTALL
THE MOUNTING
holes for
the dotted
line.
5. Review
4. Remove
the Installation
the template
from the
PLATE
installation
situation.
Instruction
rear wall.
book for
your
Darle vuelta
versión
en Español.
a la hoja
para consultar
la
Locate
mounting
and mark
holes to
IMPORTAN
plate.
T:
align with
holes
in the
LOCATE
THE CENTERL
AT LEAST
MARK
INE.
ONE STUD
ON EITHER
SPACED
THE LOCATION
FOR 2
SIDE OF
AREA.
TOGGLE
BOLTS
IN THE
ADDITION
AL, EVENLY
MOUNTIN
G PLATE
Trim the
rear wall
template
along
the dotted
line.
Locate
mounting
plate.
and mark
holes to
align with
IMPORTA
NT:
holes in
the
THE CENTERL
LOCATE
AT LEAST
MARK
INE.
ONE STUD
ON EITHER
SPACED
THE LOCATION
FOR 2
SIDE OF
AREA.
TOGGLE
BOLTS
IN THE
ADDITION
AL, EVENLY
MOUNTIN
G PLATE
C
30
to Cooktop
to Cooktop
30
EN-20
Publicidad
