Publicidad
Idiomas disponibles
Idiomas disponibles
Fully pull trigger and motor will start. (nail will drive into
u
work surface).
Release trigger.
u
Lift contact trip off work surface.
u
Repeat the above 4 steps for next application
u
Preparing the tool
Warning! NEVER spray or in any other way apply oil, lubri-
cants or cleaning solvents inside the tool. This can seriously
affect the life and performance of the tool.
Warning! The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
Read the Safety Instruction section of this manual.
u
Wear eye and ear protection.
u
Remove battery from tool and fully charge.
u
Ensure magazine is empty of all fasteners.
u
Check for smooth and proper operation of contact trip and
u
pusher assemblies. Do not use tool if either assembly is
not functioning properly.
Keep tool pointed away from yourself and others.
u
Insert fully charged battery pack.
u
Loading the Tool
Warning! Keep the tool pointed away from yourself and
others. Serious personal injury may result.
!
Warning
Never load nails with the contact trip or trigger
activated.
!
Warning
Always remove battery pack before loading or
unloading nails.
!
Warning
The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
!
Warning
Keep fingers clear of pusher to prevent injury.
Insert fasteners into the bottom of the magazine (9).
u
Pull pusher (10) downward until the nail follower (15) falls
u
behind the nails as shown in figure G.
Release the pusher (10).
u
Unloading the Tool
Warning!The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
Press pusher latch release button (11).
u
Manually slide nails towards the bottom of the magazine
u
(9).
Open the jam clear door (7) on the nosepiece to verify
u
there are no nails remaining.
Adjusting Depth (Fig. H)
The depth that the fastener is driven can be adjusted using
the depth adjustment wheel (3) on the side of the tool.
Warning!To reduce risk of serious injury from accidental
(Original instructions)
actuation when attempting to adjust depth, Always:
Remove battery pack.
u
Engage trigger lock-off.
u
Avoid contact with trigger during adjustments.
u
Depth settings are on a sliding scale (4). The left side indica-
ting the deepest and the right side indicating the shallowest.
To drive a nail deeper, rotate the depth adjustment wheel
u
(3) downwards. This will slide the depth adjustment indica-
tor (4) to the left on the scale.
To drive a nail shallower, rotate the depth adjustment
u
wheel (3) upwards. This will slide the depth adjustment
indicator (4) to the right on the scale.
Work lights (Fig. I)
There are work lights (5) located on each side of the nailer.
Work lights turn on upon depressing the contact trip.
Note: These work lights are for illuminating the immediate
work surface and are not intended to be used as flashlights.
Low Battery Indicator:
The work lights will flash and then turn off completely to
indicate low battery.
Jammed Nail Indicator:
The work lights will flash continually if a nail becomes jammed
in the nose piece (see Clearing a jammed nail).
Stall Release (Fig. J)
Warning! If a stall occurs, the tool will disable itself and will
require you to reset it. To do so, follow instructions on clearing
a stalled condition. Next remove battery pack and then rein-
sert battery pack. The tool will now be operational. If the nailer
is used in a rigorous application where all available energy in
the motor is used to drive a fastener, the tool may stall. The
driver blade did not complete the drive cycle and the jam/stall
indicator will flash. Rotate the stall release lever (6) on the tool
and the mechanism will release as shown in figure G.
Note! The tool will disable itself and not reset until the battery
pack has been removed and reinserted. If the unit continues
to stall please review the material and fastener length to be
sure that it is not too rigorous an application. If the driver
blade does not automatically return to the home position after
rotating the stall release lever, proceed to "clearing a jammed
nail".
ENGLISH
29
Publicidad
