KIKKA BOO i-DRIVE Instrucciones De Uso página 12

IMPORTANT! KEEP FOR FUTURE REFERENCE!
EN
READ CAREFULLY!
2.30 Release the shoulder strap from the shoulder clip, and finally pull the shoulder strap and shoulder pad out.
2.31 Pull out the adjusting strap and release the two shoulder straps from the three-way connection metal clip as shown in the picture.
2.32 Press the red button to open the buckle.
2.33 Pass the buckle (without insertion) through the hole.
2.34 Open the upholstery like the picture, fasten the insertion to buckle, open the buckle cover under the base, put the buckle to the buckle hole and finally close the cover.
2.35 Clear up the upholstery as shown in the picture.
INSTALLATION FOR ISOFIX
NOTICE!
Child safety seats are also available with the ISOFIX guider (If your car is not equipped with the standard ISOFIX guider).
2.36-2.37 If it will be more convenient to install, please clamp the ISOFIX guider on an ISOFIX fixed point on the car.
NOTICE!
You can recline your car seat to the proper position if the angle of the car seat can adjust, it will be more convenient to install the ISOFIX.
2.38-2.40 Push the isofix to the ISOFIX guider until locking the ISOFIX, than push the baby car seat toward to the car seat until meeting it.
THE WAY TO REMOVE ISOFIX
2.41 Press the "ISOFIX release button" on both side and hear the "click" sound, then remove the seat. Only when the left and right ISOFIX show red indicator, it means that ISOFIX has
unlocked correctly.
THE INSTALLATION METHOD FOR TOP TETHER
2.42-2.43 Open the back cover, take out the top tether and close the back cover. Release the top tether strap by pressing the release button and pulling the strap to longer.
2.44-2.45 Pass top tether under the headrest of the car seat.
2.46 Clip the top tether.There are three fixed points anchor behind the car seat, please choose the one according to your car position of anchor.
NOTICE!
Pass the top tether belt under the pillow of the car seat (if the piIIow can not adjust, please pass it upon the pillow).
2.47 Fasten the belt by pulling the belt backwards until the indicator shows green.
III. INSTALLATION METHOD
USE ISOFIX+ TOP TETHER TO INSTALL THE CHILD SAFETY SEAT IN REARWARD FACING POSITION
(SUITABLE FOR CHILDREN 40- 105CM / < 18KG)
3.1 When installing the child safety seat in rearward facing, please follow the 2.18-2.25 method, rotate the seat to the rearward facing position (as shown in picture) then follow the
method 2.36-2.40 to install ISOFIX in the car seat.
WARNING!
Under no circumstances the car seat can be used in a position that has airbags.
3.2 Pull out the top tether and pass it on the belt guider on the back of the car seat from top to bottom, press it (as shown in picture) and finally follow the method 2.42-2.47.
USE ISOFIX+ TOP TETHER TO INSTALL THE CHILD SAFETY SEAT IN FORWARD FACING POSITION
(SUITABLE FOR CHILDREN 76- 105 CM / < 18KG)
NOTICE!
When the child's weight is below 9kg, the child safety seat must be with Rearward facing installation.
3.3
•
For adjusting the child safety seat to the suitable position, please follow method 2.12-2.15
•
For installing ISOFIX to the ISOFIX fixed anchor in the car, please follow method 2.36-2.40
•
For installing top tether to the top tether fixed anchor in the car, please follow method 2.42-2.47
•
Check the child safety seat if it is installed correctly.
•
Fix the child, please follow 2.26
USE ISOFIX ATTACHMENT+ 3-POINT SEAT BELT TO INSTALL THE CHILD SAFETY SEAT IN FORWARD FACING POSITION
(SUITABLE FOR CHILDREN 100-150 CM)
•
Remove the 5-point safety belt first.
•
Meet the ISOFIX and ISOFIX anchor points on the car seat.
•
Put the child safety seat on the car seat and adjust the child safety seat to the suitable position.
•
The belt of the car seat passes through the seat belt guider and passes around the child's shoulder.
•
The belly belt of the car seat belt passes through the belly belt guider and passes the child's pelvis.
•
Fasten the car seat belt.
NOTICE!
When used from 135-150cm, may not fit in all vehicles.
ENGLISH