Publicidad
Idiomas disponibles
Idiomas disponibles
m
z
C)
r
en
::J:
3.
MOUNTING AND DISMOUNTING THE LENS
(1)
Mounting
(Fig.
5)
While pushing the Lens
Lock Release
toward the
arrow,
lift up the
Lens
Lock
.
The
lens Lock
will
now remain
in
lifted position. Next, hold the
lens with the aperture scale
up,
hook
the lensboard bottom
on
the lens
mounting then press the lens against the
lens mounting. The Lens Lock
will automatically return to
locking
position
to lock
the
lens in pace.
Lens Lock Release
(Fig
.
5-A)
Lens Lock
(Fig.
5-B)
:;:
If the lens is not correctly
mounted
,
faulty
connection wi
ll
cause
the
Stand-by Monitor to
blink,
so you'll have
to remount
the lens correctly.
(2)
Dismounting
(Fig.
6)
While
supporting
the
lens with
one hand, push
back
the
Lens
Lock
Re-
lease to
the
arrow and lift the Lens
Lock.
:;:
To prevent
dropping the lens
,
be sure
to
support
it
with one
hand
se-
curely while
dismounting it.
*
A
conventional type
interchangeable
lens (GX
type)
can
be used. In
this
case
,
however, the
lens does
not work to count total number
of
shots.
4.
MOUNTING AND DISMOUNTING THE ROLL FILM HOLDER
m
AND
REVOLVING IT
(1)
Mounting
(Fig.
7)
Line up
the upper
edge
of the
Roll
Film
Holder
III with
the
hyphenated
reference line on
the Camera Back
and,
while pressing the
Roll Film
Holder III against
the Camera
Back,
turn
it toward
the
arrow so
that it
locks into
horizontal
position with a click
.
Hyphenated
reference
line
(Fig. 7-A)
Dismounting (Fig.
7-B)
Mounting
(Fig.
7-C)
Revolving Lock
(Fig
.
7-D)
(2)
Dismounting
(Fig.
8)
First, make sure the
Dark
Slide
is
inserted
in the Roll
Film
Holder
Ill.
Next,
while pushing
the Revolving Lock
of
the
camera body,
turn the Roll
Film Holder
III 45°
to
the left and
dismount
it.
The Film
Holder
is set horizontally
(Fig. 8-A)
(3)
Revolving (Fig.
9,
10)
To
change
the position of the
Film Holder
from
horizontal
to vertical
,
turn
it
90°
to the right
,
and from vertical
to
horizontal turn
it
90°
to the
left.
(You
'll
have to
press
in
the
Revolving
Lock to do
it.) It will fall into
the
co
rrect vertical or horizontal position with a
loud
click.
Vertical
to
horizontal
(Fig.
9-A)
Horizontal to
vertical
(Fig. 9-B)
Revolving Lock (Fig.
9-C)
The Film
Holder is set
vertically
(Fig.
10-A)
:;:
Revolving
can be
'done with the Dark
Slide
removed.
:;:
You'll
have
to press in the Revolving Lock to mount,
dismount,
and
revolve
the
Roll
Film
Holder Ill
,
but once you
press
it in and
move
the
Holder
even
slightly,
you can take your finger off
it.
There
is
no need
to hold
it
down
.
(4) Dark Slide handling
(Fig.
11)
Th
e camera has the
Dark
Slide
Pocket. When taking
pictures,
be
sure
to
insert the sliding cover in this pocket so that you won 't
misplace
or
lose
it.
:;:
The
roll
film holder
III cannot be dismounted with
the
sliding cover
drawn
out as it is
locked
.
Detach
the
roll fi
lm
holder
III after inserting
the
sliding
cover.
II-
LCD INFORMATION PANEL
1. STAND-BY MONITOR
The LCD
wi
ll
show you
the
condition of the
batteries, whether the
cam-
era is
ready
to take pictures
or
not
(whether the
lens
and
Film Holder
are
properly mounted or
not,
whether
the Sliding
Cover
is
in
or
out,
and
whether the
Shutter
Speed Selector is
set
to the
se lective
or
AE
mode),
and whether the camera
is
behaving
normally
or
not (action of the
shut-
ter
blades,
movements
of the
mirror
and
light
shield
and behavior of the
faulty film
transport)
.
(1) Readiness to take pictures (Fig. 12)
The lighting
or blinking LCD
wi
ll
tell you whether you
can
just press down
the Shutter Release to take
your
picture
or
not. This
signal
is based
on
whether
the
contacts are correctly connected or
not
when the
Lens
and
Film
Holder are mounted
or,
whether the
Sliding
Cover is in or
out,
and
whether the
Shutter
Speed Selector is set
to
the selective or
AE
mode.
• Camera ready
If
the
camera is ready
to take
pictures,
the
LCD
on the Camera will
turn
off except
for the battery
mark,
and
the LCD
on
the Roll Film Holder
III
will turn
on
indicating
all the camera illustrations
.
• Camera unready
If
anyone of
the
conditions ju
st mentioned
is
not in
proper
order,
A
will
blink
and
the camera
won't
operate.
At
the
same
time, the camera illus-
tration of the unready part
bl inks
on the LCD
of
the
Roll Film Holder
Ill
.
Check
the
condition
again
.
:;:
When
the camera behaves abnormally and the shutter release is
pressed down, the Electronic Warning
Buzzer
will buzz two times
,
A
of the
LCD
on the
camera
and camera illustration
(part
in
the
abnor-
mal behavior) of the
LCD
on the roll film holder III continue to
blink.
Publicidad
