Publicidad
Idiomas disponibles
Idiomas disponibles
I
WARNING
I
To avoid electrical
shock which
can cause
severe
personal
injury or death,
green
ground
wire must remain
attached
to hinge.
4.
Unplug top hinge wire connectors. Do not remove
green ground wire from hinge (Freezer door ice and
water dispensing units only). Remove top hinge
screws. Carefully lift and remove top hinges.
Freezer door only
Wire connectors
Top hinge
..qreenground wire
5.
Carefully lift doors off bottom hinge.
6.
Replace doors by performing steps 1-5 in reverse
order.
Install Water Filtration
Cartridge
(some
models)
Bypass cartridge must be removed before connecting
water to unit.
1.
Remove bypass cartridge from water filter head in rear
right corner of refrigerator section. Twist cartridge
counterclockwise IA turn and pull down to remove.
Save bypass for use at a later date.
2.
See Water Filtration System Installation and Operating
Instructions provided with water filter cartridge for filter
installation and operation.
Connecting
Water
Supply
(some
models)
I
WARNING
I
To avoid electrical shock which can cause severe
personal injuryor death, disconnect power to refrigerator
before connecting water supply.After connecting water
supply, connect power.
CAUTION
To avoid
property
damage,
observe
the following:
•
Verify that bypass
cartridge
has been removed
and
replaced
with water filter
in water filter assembly.
•
Confirm
water
pressure
to water valve
is between
20 and 120 pounds
per square
inch.
•
Tighten
nut by hand to avoid cross threading.
Finish
tightening
nuts with pliers
and wrenches.
Do not
overtighten.
•
Check
for water
leaks and correct
if necessary
before
returning
refrigerator
to normal
location
and 24 hours
after connecting.
•
If water
filter will be installed,
water
pressure
to
water valve
must be a minimum
of 35 pounds
per square
inch.
Important
• Before connecting water supply, contact a plumber to
connect copper tubing to household plumbing in
compliance with local codes and ordinances.
• Do not use a self-piercing
or 3/16"(4.8 mm) saddle
valve. Both reduce water flow, can develop sediment
build up, and may cause leaks if repair is attempted. The
correct type of shut off valve requires a 1/#,(6.35 mm)
hole to be drilled in water supply pipe prior to valve
attachment.
• Do not use plastic tubing.
• Do not run tubing from water supply in a location where
the temperature may fall below 55 ° R
Materials Required
1/#,(6 mm) flexible copper tubing
Length of copper tubing must reach from water supply
connection plus an additional 8' (2 m) for service loop
behind refrigerator.
Procedure
1.
Remove plastic cap from water valve inlet port. Place
brass nut and brass sleeve on copper tubing. Insert
copper tubing into water valve inlet port. Hand-tighten
brass nut on copper tubing to water valve inlet port.
Use a wrench to finish tightening nut. Be careful not to
overtighten nut. Confirm copper tubing is secure by
pulling on copper tubing.
II
I, III Pc,amp
Copper tubing°
Brass nut
] _
I _ Water valve inlet
_
connection
2.
Create service loop using extreme care to avoid
kinks. Secure copper tubing to refrigerator
cabinet with "P" clamp.
3.
Turn on water supply to refrigerator and check for
leaks. Correct any leaks.
4.
Push refrigerator into opening. Recheck for leaks
after 24 hours.
Controls
This refrigerator is designed to operate at normal
household temperatures of 55 ° to 110°F (13 ° to 43°C).
Refrigerator
and Freezer
Controls
Refrigerator and freezer controls are located on upper
rear wall of refrigerator section.
CONTROL
DIRECTIONS
FREEZER
REFRIGERATOR
!
!
•
DASHES
SHOW
FACTORY
3
4
3
4
•
CHANGE
ONE
CONTROL
AT
•
•
A TIME
WAIT 24 HOURS
2
5
BETWEEN
ADJ
STMSNTS
2
5
•
FREEZER
AD J STMSNT
ALSO
EFFECTS
RE FR GSRATOR
TEMPERATURE
WA R
EST
I, N ARMEST
OFF COLDES
T
m
!;1
I,!,1
5
Publicidad
