Publicidad
6
4. OPTICAL
Optical input jack.
5. HDMI eARC/ARC
Connect to your TVs HDMI (eARC/ARC) port.
Initial set up
Remote control operation
The provided remote control allows the unit to be operated from a
distance.
• Even if the remote control is operated within the eff ective range of 6m,
operation may be impossible if there are any obstacles between the
unit and the remote control.
• If the remote control is operated near other products which generate
infrared rays, or if other remote control devices using infrared rays are
used near the unit, it may operate incorrectly. Conversely, the other
products may operate incorrectly.
Battery installation
1. To open the battery compartment, push your thumb down on to the
battery compartment cover and slide it down.
2. Fit two AAA batteries observing polarity +/- as shown. When
replacing the batteries, use only the same type of battery supplied.
3. Re-fi t the battery cover and clip it in place.
Placement
If your TV is placed on a table or a wall, you can place the unit on a fl at
surface in front of or underneath the TV, centred with the TV screen.
Connections
Dolby Atmos
Dolby Atmos delivers an unparalleled audio experience, featuring
overhead sound and the signature richness, clarity, and power of Dolby
audio.
To listen to Dolby Atmos audio through your soundbar, you will need
Dolby Atmos content delivered to your TV.
Dolby Atmos content is available via some broadcast services, streaming
services or via external devices connected by HDMI e.g. a Dolby Atmos
compatible games console or Blu-ray player.
For more information on Dolby Atmos content availability visit dolby.
com.
Using Dolby Atmos
Dolby Atmos is available only on TV (HDMI) source. For the details of the
connection, please refer to "HDMI eARC/ARC".
To experience Dolby Atmos through HDMI OUT (eARC/ARC), ensure your
TV or source device HDMI eARC/ARC output is set to PASS THROUGH,
AUTO, BITSTREAM or other equivalent mode. This setting is usually
adjusted via the menu of your TV or source device.
Using eARC
The "e" in eARC stands for "enhanced". AV equipment with eARC HDMI
sockets enjoy greater bandwidth and speed compared to regular ARC
sockets. This allows a wider frequency range and uncompressed audio
resulting in more detailed, rich and vibrant sound delivery. Using eARC
HDMI ports and compatible cables also allows audio formats such as
Dolby Atmos to be played at their full capacity. Your soundbar comes
with a high-speed HDMI cable to take advantage of the extra bandwidth
off ered by eARC.
HDMI eARC/ARC
(Refer to
4 on page 3).
The eARC (enhanced Audio Return Channel) function allows you to send
audio from your eARC/ARC- compliant TV to your sound bar through
a single HDMI connection. To enjoy the eARC/ARC function, please
ensure your TV is both HDMI-CEC and eARC/ARC compliant and set up
accordingly. When correctly set up, you can use your TV remote control
to adjust the volume output of the sound bar.
• Connect the included HDMI cable from the units HDMI OUT socket to
the HDMI (eARC/ARC) socket on your eARC/ARC compliant TV.
TIPS:
– Your TV must support the HDMI-CEC and eARC/ARC function and this
must be set to "ON" or "ACTIVE" in the TV settings menu.
– The setting method of HDMI-CEC and eARC/ARC may diff er depending
on the TV. For details about eARC/ARC function, please refer to your TV
manual.
– Only HDMI cables of version 2.0 or higher can support the eARC/ARC
function.
Optical
(Refer to
5 on page 3).
• Remove the protective cap of the OPTICAL socket, then connect an
OPTICAL cable (not included) to the TV's OPTICAL OUT socket and the
OPTICAL socket on the unit.
Audio in
(Refer to
6 on page 3).
A. Use a RCA to 3.5mm audio cable (not included) to connect the TV's
or external audio device's audio output sockets to the AUDIO IN socket
on the unit.
B. Use a 3.5mm to 3.5mm audio cable (not included) to connect the
TV's or external audio device headphone socket to the AUDIO IN socket
on the unit.
TIP:
– When you use the headphone output on the TV set, you will be able to
adjust the volume level directly using the TV remote control.
Connect to power
(Refer to
7 on page 3).
• Before connecting the DC adapter, ensure you have completed all
other connections.
• Risk of product damage! Ensure that the power supply voltage corre-
sponds to the voltage printed on the back or the underside of the unit.
• Connect the power cable to the DC Socket of the unit and then into a
power socket.
Basic operation
Standby/ON
• When you fi rst connect the unit to the power socket, the unit will be
in STANDBY mode.
• Press
on the remote control or the soundbar to switch the sound-
bar ON or OFF.
• Disconnect the plug from the power wall socket if you want to switch
the unit off completely.
• With HDMI CEC control, you can use your TV remote to increase/decre-
ase the soundbars volume.
Change source
• Short press INPUT to change between TV, OPTICAL, AUDIO IN and
BLUETOOTH. The units LED will light up under the source you select.
Publicidad
