Global Section; Mic/Aux Section; Midi Section - Pioneer DJM-T1 Manual De Instrucciones

Global section

SNAP
QUANTIZE
1 SNAP (QUANTIZE) button
! Press:
Turns the TRAKTOR snap function on and off.
When the snap function is on, the cue and loop points are set to the same
position as the nearest [Beat Grid].
! [SHIFT] + press:
Turns the TRAKTOR quantize function on and off.
When the quantize function is on, movement to the cue and loop points is
synchronized with the timing of the beats.

MIC/AUX section

MIC OFF AUX
INPUT SELECT
1
1 INPUT SELECT switch
Switches the audio input between the external device and the microphone.
— [AUX]: The external device connected to the [AUX] terminals is selected.
— [OFF]: The [MIC/AUX] channel is turned off.
— [MIC]: The microphone connected to the [MIC] terminal is selected.
! The sound input to the [MIC] and [AUX] terminals is mixed with the [CH 1]
and [CH 2] sound that has passed through the crossfader.
2 LEVEL control
Adjusts the audio level input to the [MIC] and [AUX] terminals.
3 EQ (HI, LOW) controls
These adjust the tone of the [MIC/AUX] channel.
Inputting the sound of a microphone or
external device
1 Connect the external device to the [MIC] or [AUX] terminal.
2 Switch the [INPUT SELECT] switch.
3 Turn the [LEVEL] control.
Adjust the audio level input to the [MIC] or [AUX] terminal.
! Pay attention that rotating to the extreme right position outputs a very loud
sound.
 Adjusting the sound quality
Turn the [EQ (HI, LOW)] controls.
Refer to Specifications on page 32 for the range of sound that can be adjusted by
each control.
1
(SHIFT)+
1 1
0 12 12 12 12
LEVEL LOW EQ HI
2 3

MIDI section

This unit outputs the operation information of buttons and controls in universal MIDI
format.
When connected by USB cable to a computer on which a MIDI-compatible DJ soft-
ware program is installed, the DJ software can be operated from this unit.
Operating DJ software using the MIDI function
Install the DJ software on your computer in advance. Also, adjust the audio and
MIDI settings for the DJ software.
! For MIDI channel setting instructions, see Setting the MIDI channel on page 26.
! For the messages output by this unit, see MIDI assignment map on page 28.
1 Connect this unit's [USB] terminal to the computer.
For instructions on connections, see Connecting the input/output terminals on page 11.
2 Launch the DJ software.
3 Press the [CH 1] button.
The MIDI functions of the [CH 1] side's [TRIM] control, [EQ (HI, MID, LOW)] con-
trols, [CUE (TAP)] button, channel fader and crossfader A are activated.
! Crossfader A is the [CH 1] volume adjustment function extracted from the cross-
fader's volume adjustment function.
! When the [CH 1] button is pressed again, the above MIDI functions are
deactivated.
4 Press the [CH 2] button.
The MIDI functions of the [CH 2] side's [TRIM] control, [EQ (HI, MID, LOW)] con-
trols, [CUE (TAP)] button, channel fader and crossfader B are activated.
! Crossfader B is the [CH 2] volume adjustment function extracted from the cross-
fader's volume adjustment function.
! When the [CH 2] button is pressed again, the above MIDI functions are
deactivated.
5 Operate a button or control in the mixer section.
The MIDI message for the button or control being operated is sent.
6 Operate a button or control other than one in the mixer
section.
The MIDI message for the button or control being operated is sent.
! The MIDI functions for the buttons and controls in the browse, transport, effect,
hot cue/sampler and global sections are always activated, regardless of the [CH
1] and [CH 2] buttons.
MIDI
ON / OFF
CH1 CH2
1
23
En