Startup; Operation - GGP ITALY MP2 504 Serie Manual De Instrucciones

Ocultar thumbs Ver también para MP2 504 Serie:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

6.2.1
General safety check
Object
Cutting means 
Rear discharge guard; 
grass catcher
Side discharge guard,
side discharge chute
Engine brake lever 
/ cutting means
Handgrip and starter cable.
Screws/nuts on the machine 
and on the cutting means
Fuel lines and connections.
Oil lines
Spark plug cap
Test driving
6.2.2
Machine operating test
Action
Start the machine (par. 6.3)
Engage the drive lever
Disengage the drive lever
Release the engine /
cutting means brake lever
If any of the results fails to match the
indications provided in the tables, do not use
the machine! Contact a service centre to have
it checked and repaired if necessary.
6.3

STARTUP

NOTE Start up the machine on a flat
surface without obstacles or high grass.
6.3.1
Manual ignition handgrip models
1.
For cold starts: move the throttle to the "Choke" 
engaged position (fig. 6.A) (if provided).
2.
Pullthe engine / cutting means brake 
lever towards the handle (fig. 15.A).
NOTE Keep pulling the engine / cutting
means brake lever or the engine will stop.
3.
Grab hold of the starter handgrip and tug the
starter cable firmly to start the engine (fig. 15.B).
Result
Not damaged or worn. 
Good condition. No
damage. Properly installed.
Good condition. No
damage. Properly installed.
The lever must move 
freely, it must not need 
forcing and should return
automatically and rapidly 
back to the neutral position.
The cable must be intact.
Correctly tightened 
(not loose)
No leaks.
No leaks. 
No damage.
Connected to the
spark plug itself
No abnormal vibrations.
No abnormal sound
Result
The cutting means 
must move.
The wheels should move 
the machine forward.
The wheels should stop 
and the machine stops 
moving forward.
The engine must switch off 
and the cutting means must 
stop within a few seconds.
4.
When the engine has
to the full speed position (if fitted).
NOTE Using the choke when the engine
is already warm can foul the spark plugs and
cause the engine to run erratically.
6.3.2
Electric push-button ignition control models
1.
Insert the supplied battery in the relative 
engine compartment (fig. 16.A). (follow the 
instructions provided in the engine manual)
2.
Insert the key as far as possible (if provided) (fig. 16.B).
3.
Pullthe engine cutting means brake lever 
towards the handle (fig. 15.A).
NOTE Keep pulling the engine / cutting
means brake lever or the engine will stop.
4.
Press and hold the ignition button unyil 
the engine switches on. (fig. 16.D).
6.4

OPERATION

IMPORTANT When working, always keep a safe distance
from the cutting means, given by the length of the handle.
6.4.1
Grass cutting
Start moving forward and mowing in the grass area;
1.
2.
Regulate the forward speed and the cutting 
height (par. 5.7) considering the conditions of
the lawn (the height, density and dampness of 
the grass) and the amount of grass collected; 
For mulching or rear grass discharge: always avoid 
removing a large quantity of grass. Never cut more than 
one third of the total grass height per single pass (fig. 17).
3.
The appearance of the lawn will improve if you alternate 
cutting in both directions at the same height (fig. 18).
For side discharge: it is best to mow in a pattern where 
cut grass is not discharged on the grass still to be cut.
6.4.2
Suggestions for maintaining a nice lawn
Each type of grass has different characteristics and may 
thus require different ways of caring for the lawn; always 
read the instructions on seed boxes for mowing height 
in relation to the growing conditions in the work area.
Keep in mind that most grass is made up of a stem 
and one or more leaves. If leaves are fully cut, the 
lawn is damaged and growth is more difficult.
The following indications generally apply:
• cutting too low tears and uproots the grass, 
giving it a "spotted" appearance;
• in the summer, cutting must be higher to 
prevent the ground from drying;
• do not cut wet grass; this could reduce cutting means 
efficiency due to sticky grass and tear the lawn;
• for particularly high grass, initially mow at the 
maximum height allowed by the machine 
then mow again after two or three days.
EN - 7
started, shift the throttle

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Mp2 554 serie

Tabla de contenido