Overhead Rigging - JB Systems Light SPACE 3 Laser Manual De Instrucciones

ENGLISH

OVERHEAD RIGGING

 Important: The installation must be carried out by qualified service personal only.
Improper installation can result in serious injuries and/or damage to property.
Overhead rigging requires extensive experience! Working load limits should be
respected, certified installation materials should be used, the installed device
should be inspected regularly for safety.
 Make sure the area below the installation
place is free from unwanted persons during
rigging, de-rigging and servicing.
 Locate the fixture in a well ventilated spot, far
away from any flammable materials and/or
liquids. The fixture must be fixed at least
50cm from surrounding walls.
 The device should be installed out of reach of
people and outside areas where persons may
walk by or be seated.
 Before rigging make sure that the installation
area can hold a minimum point load of
10times the device's weight.
 Always use a certified safety cable that can hold 12times the weight of the device when
installing the unit. This secondary safety attachment should be installed in a way that no
part of the installation can drop more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be
considered!
 Don't cover any ventilation openings as this may result in overheating.
 The operator has to make sure that the safety-relating and machine-technical
installations are approved by an expert before using them for the first time. The
installations should be inspected every year by a skilled person to be sure that safety is
still optimal.
CAUTION EYEDAMAGE: Always position the laser in a way that
prevents the audience from looking directly into the laser beams. The
installation should assure that the beam will not strike the audience.
HOW TO SET UP AND CONTROL THE UNIT
 Regular breaks during operation are essential to maximize the life of this device as it is
not designed for continual use.
 Do not switch the unit on and off in short time intervals as this reduces the lamp life.
 Always unplug the unit when it is not used for a longer time. or before replacing the bulb
or start servicing.
 In the event of serious operating problems, stop using the fixture and contact your dealer
immediately.
 Important: Never look directly into the laser beam! Don't use the effect in the presence
of persons suffering from epilepsy.
JB SYSTEMS
®
USER MANUAL
5/54 SPACE 3 Laser
ENGLISH
You can operate the unit in 5 ways:
1) MUSIC CONTROLLED MODE:
The laser runs a preprogrammed sequence to the rhythm of the music. Select this mode
when only 1 laser is used (standalone) or when the laser is placed as the first (master)
unit in a chain with several Space3 lasers.
 Press the FUNC-button until the display shows "MUS"
 Press the ENTER-button to confirm your choice.
 Put on some music and adjust the MUSIC SENSITIVITY-knob (9) until the laser works
nicely to the rhythm of the music.
You can connect several SPACE3 lasers together: just put the first unit of the chain in
"Music mode" and all other units in "Slave mode" to make them all work in perfect sync!
Note: When no music is detected, the laser output will be shut off (blackout).
2) FULL AUTOMATIC MODE:
The laser automatically runs a preprogrammed sequence. Select this mode when only 1
laser is used (standalone) or when the laser is placed as the first (master) unit in a chain
with several Space3 lasers.
 Press the FUNC-button until the display shows "AUt"
 Press the ENTER-button to confirm your choice.
The laser automatically runs a preprogrammed sequence.
You can connect several SPACE3 lasers together. Please put the first unit of the chain
in "Automatic mode" and all other units in "Slave mode" to make them all work in perfect
sync!
3) SLAVE MODE:
The laser follows the instructions given by the first Space3 laser (master) in the chain.
 Connect the DMX input of the laser to the DMX output of the previous laser in the
chain.
 Press the FUNC-button until the display shows "SLA"
 Press the ENTER-button to confirm your choice.
You can connect several SPACE3 lasers together. Please put the first unit of the chain
in "Music or automatic mode" and all other units in "Slave mode" to make them all work
in perfect sync!
4) EASY CONTROLLER MODE:
An optional CA-8 controller can be connected so you can control the laser
from a distance. When several Space3 lasers are connected in
master/slave, you should connect the CA-8 controller to the first unit in the
chain. All units will follow the instructions given by the CA-8 remote.
 Connect the CA-8 controller to the remote controller input (8) on the
back.
 Press the FUNC-button until the display shows "CA8"
 Press the ENTER-button to confirm your choice.
JB SYSTEMS
®
USER MANUAL
6/54 SPACE 3 Laser