Publicidad
Idiomas disponibles
Idiomas disponibles
5
INSTALLATION AND COMMISSIONING
5.1
Unpacking the machine:
Machines are delivered from our works on pallets, strapped and protected with cardboard. First of all,
the packaging must be examined and any damage caused in transit must be declared directly to the
carrier.
A. Remove the cardboard and the packaging bag from the machine.
B. Remove straps, taking particular care when they are released by cutting.
C. Detach the machine from its pallet by removing the wooden battens wedging the castors.
D. Take the machine off the pallet. Make sure you do this with at least two people in order to
lower it as gently as possible onto the floor.
E. Please fit the adjustable bagger stop to the bagger (fig.10, n°33).
After unpacking your machine, check that it has not been damaged in transit. Notify
us of any defects.
If your machine has been supplied with a base (optional):
A. Fit the castors supplied to the base, taking care to fit the braked castors at the front.
B. With at least two people, place the machine on the base.
C. Remove the crumb tray from the machine.
D. Insert the silent block bushes supplied between the machine and the base (fig.4, n°21).
E. From the inside of the machine, insert the screws (fig.4, n°20) and washers supplied into the
corresponding holes in the machine frame.
F. Pass the screws through the machine, the silent block bushings and the base and tighten the
assembly with the nuts supplied (fig.4, n°22).
5.2
Positioning:
In order to achieve excellent performance and long-term reliability, choose a location that is:
Well ventilated, shielded from direct sunlight and away from sources of heat, with a sturdy
surface free from vibration.
5.3
Electrical connection:
IMPORTANT: This machine must be earthed.
It is recommended that the system be protected with a fuse and an RCD.
Your mains electricity supply to the machine must be protected as indicated below:
9
English
- North America: 15 A protection;
- Rest of the world: 16 A protection.
For machines equipped with a variable speed drive, it is imperative that they be connected to a
junction box on a circuit fitted with a 300 mA RCD.
Note: Any problem resulting from any other type of connection will not be covered under warranty.
Before connecting your machine to the mains supply and in order to prevent the motor from burning
out when it is switched on, it is important to check that the mains supply matches the machine
specification (see machine nameplate).
This machine complies with Machinery Directives 2006/42, 2006/95, 2004/108 and is CE marked as
proof of this.
Please familiarise yourself with the safety pictograms displayed on the machine:
This pictogram indicates a cut hazard. You will find it at the front of the machine
around the loaf positioning area (fig.9, n°29).
You will find the circuit diagram for the machine on the back of the electrical
enclosure door (fig.9, n°30).
This pictogram indicates an electrocution hazard. Please isolate the machine
before carrying out any work on it. You will find it at the back of the machine close
to the power cable and inside the machine on the electrical enclosure (fig.9, n°31).
This pictogram indicates a contact with moving parts hazard. You will find it on the
front door (fig.9, n°28).
5.4
Commissioning:
Before commissioning, ensure that there are no extraneous objects interfering with the machine's
moving parts.
For machine operation, please refer to the "Operation" chapter.
5.5
Danger:
If the user or the machine is in danger, you must use the main isolator switch to cut the power supply
to the machine.
Remove the plug from the power socket before any maintenance and/or servicing work.
Do not touch the blade, even if it is stationary.
To replace the blade, have the work done by your approved dealer.
Always wear cut-resistant gloves when replacing the blade or when working in the vicinity of the
blade.
English
10
Publicidad
