Publicidad
Idiomas disponibles
Idiomas disponibles
Skimmer Infinity
Installation in timber pool frame - lined with liner
1
21
2
16
Figure 1.
A-A ( 1 : 3 )
19
18
Figure 2.
A-A ( 1 : 3 )
Install as follows:
1. Make a hole in the frame for the skimmer, dimensions and location as shown in Fig. 3.
2. Install and secure the skimmer in the pool frame as shown. The water surface must be
30 – 40 mm below the top edge of the skimmer. The skimmer's flange must be level with
the finished pool wall. To prevent subsidence, the skimmer must be secured with, for
F-F ( 1 : 3 )
example, pressure-impregnated joists in the pool frame.
3. Connect pipe coupling to the pool circulation using a suitable thread sealant.
4. The drainage pipe (14) is glued to the pipe muff (15) using a suitable PVC adhesive
and fitted in the skimmer with the enclosed gasket and nipple (16). Connect pipe fittings
to the overflow.
5. Install level monitor according to instruction MA55-49.
6. Install the flap gate (17) and check that it is correctly located and can move.
7. Attach the self-adhesive gasket (7) to the front edge of the skimmer (facing the pool).
8. Put in the liner.
9. Fill the pool with enough water for the water surface to reach 5 cm below the skimmer.
F
Turn off the water.
10. Fit the outer gasket (9) and the mounting frame (10) - fasten first, then tighten crosswise.
11. Carefully cut the liner cleanly along the inside of the mounting frame (10).
12. Now, continue to fill the pool with water, until the water surface reaches the centre
of the skimmer's opening.
13. Fit the front frame (12).
14. Install/adjust the collar:
If necessary, cut the plastic collar (2) to height, so it matches the surface coating surrounding the pool.
Apply a suitable sealing compound to the underside of the collar against the skimmer.
Press the collar down against the skimmer. Secure the collar in place with the enclosed screws (21).
15. Press the cover (1) into the collar.
C
4
3
C
C
B
B
Support
for the
skimmer
B
14
n
6,5 (4x)
15
16
F
10
12
5
11
9
13
6
7
20
8
13
Unless otherwise stated:
The 3D-model is correct and made in
the middle of the tolerance zon.
Tolerances/dimensions in this
All dimensions are after
document take priority over values
Water surface
surface treatment.
found in 3D-model.
Designed by
Date of issue
Unit
E
3D-model
Unless otherwise stated:
Paul.Drotz
2021-11-01
mm
M20633-0
Tolerances/dimensions in this
document take priority over values
Trä med liner P105
found in 3D-model.
Designed by
Date of issue
Paul.Drotz
2021-11-01
Unless otherwise stated:
Tolerances/dimensions in this
document take priority over values
found in 3D-model.
Designed by
Date of issue
Paul.Drotz
2021-11-01
10
ENGLISH
4
10
10
18
12
20
7
8
B
Top edge,
liner strip
461
435
General surface profile tolerance
Threads
Edges of undefined
Surface roughness
ISO 965
shape ISO 13715
(Ra) ISO 1302
B
Tolerancing
Art.no.
Side
of
General surface profile tolerance
Threads
Edges of undefined
The 3D-model is correct and made in
ISO 8015
2
(2)
ISO 965
shape ISO 13715
the middle of the tolerance zon.
Sheet size
All dimensions are after
A2
surface treatment.
Drawing number
Revision
E
Unit
3D-model
Tolerancing
M20633 0
-
mm
M20633-0
ISO 8015
Trä med liner P105
1. Lid
General surface profile tolerance
Threads
Edges of undefined
The 3D-model is correct and made in
ISO 965
shape ISO 13715
the middle of the tolerance zon.
(incl. silicone sleeves)
All dimensions are after
surface treatment.
2. Collar
Unit
E
3D-model
Tolerancing
mm
M20633-0
ISO 8015
3. Nut M6 (4x)
Trä med liner P105
4. Edge frame
5. Countersunk screw M6x30 (4x)
6. Self-adhesive gasket 1.5 mm
7. Wall mat
8. Liner
9. Gasket 2 mm
10. Mounting frame
11. Screw M5x16 (13x)
12. Front
13. Countersunk screw M5x25 (6x)
OBS! Uppdatreade 6/4 2022
pga uppdatering till svetshuset och flytt av fästen
14. PVC drainage pipe
15. Pipe muff
0
16. Nipple incl. gasket
Unless otherwise stated:
17. Flap gate
Tolerances/dimensions in this
document take priority over values
found in 3D-model.
18. Screen basket
Designed by
Paul.Drotz
19. Skimvac plate
20. Plywood
21. Screw (2x)
Surface roughness
(Ra) ISO 1302
Art.no.
Side
of
1
(2)
Sheet size
A2
Drawing number
Revision
M20633 0
-
Figure 3.
Surface roughness
(Ra) ISO 1302
Art.no.
Side
of
1
(2)
Sheet size
A2
Drawing number
Revision
M20633 0
-
ID för mätprotokoll
General surface profile tolerance
The 3D-model is correct and made in
the middle of the tolerance zon.
All dimensions are after
surface treatment.
Date of issue
Unit
E
3D-model
Tolerancing
2021-11-02
mm
M20634-0
ISO 8015
Håltagning i träpoolstom
P105
Publicidad
