Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
1
Bit grease
2
Bit shank
3
Tool holder cap
4
Tool holder cover
5
Cut in bit shank
6
Notch in tool holder cap
7
Change ring
8
Side handle (auxiliary handle)
9
Clamp nut
10 Loosen
11 Tighten
SPECIFICATIONS
Model
Blows per minute ........................................... 950 – 1,900
Overall length ...................................................... 572 mm
Net weight............................................................... 9.3 kg
• Due to our continuing programme of research and
development, the specifications herein are subject to
change without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to enclosed safety
instructions.
ADDITIONAL SAFETY RULES
1.
Wear a hard hat (safety helmet), safety glasses
and/or face shield. It is also highly recommended
that you wear a dust mask, ear protectors and
thickly padded gloves.
2.
Be sure the bit is secured in place before opera-
tion.
3.
Under normal operation, the tool is designed to
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
4.
In cold weather or when the tool has not been
used for a long time, let the tool warm up for sev-
eral minutes by operating it under no load. This
will loosen up the lubrication. Without proper
warm-up, hammering operation is difficult.
5.
Always be sure you have a firm footing. Be sure no
one is below when using the tool in high locations.
6.
Hold the tool firmly with both hands.
7.
Keep hands away from moving parts.
8.
Do not leave the tool running. Operate the tool
only when hand-held.
9.
Do not point the tool at any one in the area when
operating. The bit could fly out and injure some-
one seriously.
Explanation of general view
12 Secures at eight different
positions back and forth
on the horizontal
13 Can be swung 360° on the
vertical and secured at any
desired position
14 Side handle base
15 Switch lever
16 ON
17 OFF
18 Adjusting dial
10. When chipping into walls, floors or wherever "live"
HM1242C
11. Do not touch the bit or parts close to the bit imme-
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing bit
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
This tool accepts 3/4" Hexagonal and 21/32" round shank
bits. Clean the bit shank and apply the bit grease pro-
vided to it before installing the bit. (Fig. 1)
Pull the tool holder cover down all the way. (Fig. 2-1)
With the cut in the bit shank aligned with the notch in the
tool holder cap, insert the bit into the tool holder. (Fig. 2-2)
Release the tool holder cover. It will return automatically
to its original position to secure the bit. (Fig. 2-3)
After installing, always make sure that the bit is securely
held in place by trying to pull it out.
To remove the bit, pull the tool holder cover down all the
way and pull the bit out.
Bit angle (Fig. 3)
The bit can be secured at 12 different angles. To change
the bit angle, slide the change ring forward, then turn the
change ring to change the bit angle. At the desired angle,
slide the change ring back to the original position. Then
turn the change ring slightly so that the bit will be secured
in place with a little click.
Side handle (auxiliary handle)
The side handle can be swung 360° on the vertical and
secured at any desired position. It also secures at eight
different positions back and forth on the horizontal. Just
loosen the clamp nut to swing the side handle to a desired
position. Then tighten the clamp nut securely. (Fig. 4)
The side handle also can be mounted in the rear groove
as shown in Fig. 5. Loosen the clamp nut and widen the
side handle base. Slide the side handle back to the rear
groove and secure it with the clamp nut. (Fig. 5)
19 Power-ON indicator lamp
(green)
20 Service indicator lamp (red)
21 Screwdriver
22 Rear cover
23 Screws
24 Brush holder cap
25 Screws
26 Socket wrench
27 Crank cap
28 Hammer grease
electrical wires may be encountered, DO NOT
TOUCH ANY METAL PARTS OF THE TOOL! Hold
the tool by the insulated grasping surfaces to pre-
vent electric shock if you chip into a "live" wire.
diately after operation; they may be extremely hot
and could burn your skin.
5
Publicidad
