Publicidad
Radio Menu Setting- Main Set
NO.
Menu
1
Squelch
2
Save
3
A/B Time
4
Double PTT
5
Bluetooth
BTRebind
6
7
Voice
8
Zone Name
9
VOX Delay
10
Mic Gain
11
Hang Up
12
Tx Channel
13
Key Define
14
Backlight
Brightness
15
16
Key Beep
17
Key Lock
18
Lock Mode
19
CH-Mode
20
S/D Mode
Scan Mode
21
22
Save CH
23
Delete CH
24
Roger
25
Time
26
Menu Exit time
27
Miss Call Set
28
Rx Info Bright Set
29
DMR TX Beep
30
FM TX Beep
31
Night Mode
32
Noise Tail
Definition
0~9 levels (In analog mode, when the Squelch level is set high, the background hiss noise will be
muted. However, only the stronger signals will be heard. If the Squelch level is set low, this will allow
lower strength signals to be heard, but the radio will now be more prone to hearing the background
hiss noise from time to time.)
Power saving ratio (It indicates the battery saving rate, the highest rate is 1�4. the higher you select,
the more power saved. at the same time, the receiving will be a little delayed, but normally we
don't feel the delay.)
Set Band A or Band B switch time from 01 to 10S.
Choose to use double PTT or not. When double PTT is on, the programmed side key function will not work.
Turn on or off the Bluetooth function. When connected to Bluetooth voice device, the Bluetooth
icon will change to red.
Confirm Bluetooth.
Voice Announcements.
Turn on the function to display zone name.
Set VOX delay time.
Set the mic gain level.
Set the digital hang up time.
①Off: when the hang-up function is off, it will transmit with the current channel contact.
② 1S ~ 10S: If the current channel has received the call within this hang-up time range, it will be
transmitted with the received contact. If it is out of the hang-up time, it will transmit with the
current channel contact.
Busy channel settings.
Key1 and Key2 short or long press functions as below: OFF, Power, Scan, radio (FM Radio）, Wake
up, Relay, Key Call 1-6, VOX, Kill (Remote kill), Zone Plus, Zone Minus, DMR slot, Promiscuous,
Manual Dial, CH-Mode, Reverse, Bluetooth , 0.5W Power, FM Call, Voltage, NOAA, Analog Monitor,
TX Digital Deviation, 1000Hz,1450Hz,1750Hz,2100Hz;
Key 1 or Key 2 long press extra functions as below:
TX-DSW, M-MONI, Tx1000, Tx1450, Tx1750, Tx2100.
Short press [*scan] button to switch SK1 or SK2 short or long press operation.
Screen backlight time：1s-120s；Cont: The backlight stays on.
Level 1-10; The higher the number, the higher the brightness.
Keyboard tone.
Choose manual or auto Lock.
Keyboard, keyboard+CH, keyboard+CH+PTT.
Frequency: Frequency+Channel number.
Name: Channel name.
CH: Channel mode.
Choose single band and dual band standby.
Carrier, Time, Search.
Time mode (TO): When the radio detects a signal it will stop scanning and will pause for 5 seconds
before scanning again even if the signal is still present.
Carrier mode (CO): When the radio detects a signal it will stop scanning and will stay on the same
frequency and will resume scanning after 5 seconds when the signal ends.
Search mode (SE): When the radio detects a signal, it will stop on that frequency and will not move
on, even if the signal ends.
Long press [*scan], it will begin to scan. Up and down key to change the scan direction, Press any
key to exit scan.
Storage channel: If displays "CH-01"，means it already a storage channel. If display "002", means it
can save it as a new channel.
Delete channel. Same operation as above.
Transmit end tone
Set local time. Use *Scan button to switch year, month, day time.
Set menu exit time.
Choose to check the miss call or not.
Choose if the led bright when receiving.
Digital transmit Talk Permit tone
Analog transmit beep tone
Switch to night mode
Repeater tail tone elimination.
05
Publicidad
