Publicidad
Idiomas disponibles
Idiomas disponibles
9 Installation
Unpacking the appliance
The packaging materials must be undamaged. Inspect
the appliance for transport damage. On no account
should a damaged appliance be connected to the
mains power supply. In case of damage, contact the
supplier.
WARNING
ELECTRIC SHOCK HAZARD!
Make sure there are no hidden cables in the wall that
could be damaged!
Assembling the appliance
Attach the suction tube: See Fig. 3.
Depending on your needs, there are 4 attachments to
choose from: −
For a dusty carpet or hard floor we recommend the
reversible floor nozzle (1). The foot button can be
used to lower or raise the integrated bristle ring for
carpets.
For corners that are difficult to reach, we recommend
the crevice nozzle (Fig. 1).
For delicate or shaped objects we recommend the
upholstery nozzle (Fig.2).
10 Operation
Only use the appliance when all parts are completely
and correctly assembled.
Before each use, make sure that the appliance is in
good condition and that the mains power cable is not
damaged.
If the mains power cable is damaged, contact the
service partner
www.ggv-service.de
prevent any danger.
1.
Place the vacuum cleaner on the floor.
2.
Insert the suction nozzle of the flexible hose
(2) into the hose connection (4) of the
vacuum cleaner housing. The hose must click
in.
3.
Push the handle of the hose onto the
telescopic tube (3).
4.
Attach the desired suction nozzle to the other
end of the telescopic tube.
5.
Use the floor nozzle (1) to clean dusty carpets
or hard floors.
6.
Use the crevice nozzle for corners that are
difficult to reach.
7.
For delicate or shaped objects, use the
upholstery nozzle.
8.
Step on the reversible floor nozzle (1) switch
to adjust the position of the brush. This
position is suitable for parquet, soft surfaces
or tiles. For carpets or mats, step again on
the brush "━".
Switching on the appliance
1.
Pull out the cable completely.
2.
Insert the plug into the socket, press the
ON/OFF button (7).
3.
When using the appliance, make sure that the
flexible hose is not blocked, twisted or
trapped.
Switching off the appliance.
1.
2.
3.
11 Cleaning and storage
CAUTION
RISK OF INJURY!
Improper use of the appliance can result in injuries.
NOTE
Switch off and unplug the appliance before cleaning.
For optimal use of the device and to ensure a longer
service life, regularly empty the container and clean
the filters.
ATTENTION
Do not immerse the motor, plug or mains power cable
in water or any other liquid (clean only with a dry
cloth).
Replacing the HEPA filter
The HEPA filter is used to filter out viruses, respirable
dusts, dust mite eggs and excretions, pollen, smoke
particles, asbestos, bacteria, various toxic dusts and
aerosols from the air.
NOTE!
Replace the HEPA filter every 6 months.
Replace the motor protection filter every 10 months.
or your dealer to
A replacement filter set consisting of:
5x
1x
1x
1x replacement filter set is included in the scope of
supply. Order more replacement filter sets for a fee at
www.ggv-service.de.
11.1
•
•
•
Cleaning the motor
Use a dry cloth for cleaning.
Do not use water, steel wool or abrasive products.
Storage when not in use for a long period of time
If the appliance is not used for a long period of time,
it is recommended to
•
•
•
The appliance is protected from dust and moisture in
its original packaging.
Press the ON/OFF button (7), pull the plug out
of the socket.
Wind up the cable with the cable winder (6).
Easily carry the floor vacuum cleaner by the
handle.
vacuum cleaner dust bags
motor protection filter,
HEPA filter
Cleaning/replacing the
motor protection filter
Open the vacuum cleaner cover using the
lock.
First remove the vacuum cleaner dust bag
and then the protective grille of the motor
filter.
Replace the motor filter and replace the
protective grille and the vacuum cleaner dust
bag.
cover it and
keep it in a dry place,
in an upright position.
Installation
Page | 17
Publicidad
