Important Remarks; Important Safety Instructions; Installation Instructions; Manual Manoeuvre - Cardin Elettronica EL Serie Manual Del Usuario

IMPORTANT REMARKS

READ THE FOLLOWING REMARKS CAREFULLY BEFORE PROCEEDING WITH THE INSTALLATION. PAY PARTICU-
LAR ATTENTION TO ALL THE PARAGRAPHS MARKED WITH THE SYMBOL
INSTRUCTIONS COULD COMPROMISE THE CORRECT WORKING ORDER OF THE SYSTEM AND CREATE DANGER
SITUATIONS FOR THE USERS OF THE SYSTEM.
• These instructions are aimed at professionally qualified "Installers of elec-
trical equipment" and must respect the local standards and regulations in
force. All materials used must be approved and must suit the environment in
which the installation is situated.
• All maintenance operations must be carried out by professionally qualified
technicians. Before carrying out any cleaning or maintenance operations
make sure the power is disconnected at the mains and that the 24V battery
supply Faston V5 has been disconnected.
• This appliance must be used exclusively for the purpose for which it has been
made. "i.e. for traffic control" of passageways with widths of 3 m and 4 m.
• The unit may be fitted both to the right and to the left of the passageway.
• The automation is fitted with an anti-tamper system protecting its internal
mechanisms. If the system is forced it will release the boom and boom holder
from the mechanism thus protecting it from damage. Normal operation can
be obtained by replacing the broken safety pin.
• This product and all its relative components has been designed and manu-
factured by Cardin Elettronica who have verified that the product conforms in
every aspect to the safety standards in force. Any non authorised modifications
are to be considered improper and therefore dangerous.
The manufacturer accepts no liability for situations arising from the use of
an electrical installation which does not conform to the local standards and
regulations in force and in particular when the earthing circuit is not efficient.

IMPORTANT SAFETY INSTRUCTIONS

It is the responsibility of the installer to make sure that the following public safety
conditions are satisfied:
1) Ensure that the gate operating installation is far enough away from the main
road to eliminate possible traffic disruptions.
2) The operator must be installed on the inside of the property and not on the
public side of the gate. The gates must not swing outwards onto a public
area.
3) The gate operator is designed for use on gates through which vehicles are
passing. Pedestrians should use a separate entrance.
4) The gate must be in full view when it is operating therefore controls must be
situated in a position where the operator can see the gate at all times.
5) At least two warning signs (similar to the example on the
right) should be placed, where they can be easily seen by
the public, in the area of the system of automatic operation.
One inside the property and one on the public side of the
installation.
These signs must be indelible and not hidden by any objects
(such as tree branches, decorative fencing etc.).
6) Make sure that the end-user is aware that children and/or
pets must not be allowed to play within the area of a gate
installation. If possible include this in the warning signs.
7) A correct earth connection is fundamental in order to guarantee the electrical
safety of the machine
8) If you have any questions about the safety of the gate operating system, do
not install the operator. Contact your dealer for technical assistance.
TECHNICAL DESCRIPTION
710/EL3424
Automation for 3 m and 4 m booms with a 24 Vdc motor.
The incorporated electronic programmer contains the power stage, the logic
control, the battery charger and the radio receiver module.
The power supply is routed to the electronics card via a separate transformer
which is housed in the same container.
710/EL324K1
3-meter boom in extruded aluminium complete with boom lights and a rubber
buffer. Flashing warning lights on the boom (using LED technology).
710/EL424K1
4-meter boom in extruded aluminium complete with boom lights and a rubber
buffer. Flashing warning lights on the boom (using LED technology).
IMPORTANT REMARKS
716/EL3424ASKU
3 m articulated boom complete with a rubber buffer. A special device inside the
bar allows it to fold backwards when the barrier is opening.
• 24 Vdc motor with tempered steel never ending screws;
- lockable flip-back upper hood in shock-proof plastic fitted with emergency
stop microswitches;
- manual release handle in nylon reinforced with glass fibre;
- irreversible second stage reduction unit with tempered steel gears and
first stage reduction worm gear in highly reliable self-lubricating POM,
mounted on a cast aluminium stator;
- zinc-plated steel geared motor support base;
- boom support levers and joints in zinc-plated steel;
- balancing springs in highly reliable steel;
- lubrication using permanently fluid grease;
- barrier bodywork in spray painted aluminium;
- lockable access door fitted with emergency stop microswitches giving
access to the manual release components;
- incorporated warning lights;
- incorporated boom lights;
- closing direction travel limit allowing the position of the boom to be
adjusted horizontally;
- adjustable opening direction travel limit with setting screw;
- self-rupturing security screw supplied with the appliance.
USER INSTRUCTIONS
Suitable differential collection, environmental friendly treatment and disposal
WARNING
contributes to avoiding negative effects on the ambient and consequently
AUTOMATIC OPENING
KEEP CLEAR
health as well as favouring the recycling of materials.
Illicitly disposing of this product by the owner is punishable by law and will
be dealt with according to the laws and standards of the individual member
nation.
Have the appliance controlled and checked at regular intervals by specialised
CHILDREN OR PETS MUST NOT
BE ALLOWED TO PLAY ON OR
NEAR THE INSTALLATION
maintenance personnel:
- Check to be carried out after the first 200.000 manoeuvres (or six months
after the installation);
Periodically check the correct operation of all safety devices (photoelectric cells
etc.). Eventual repair work or maintenance must be carried out by specialised
personnel using original spare parts.
The appliance is not suitable for continuous operation and must be adjusted
according to the model (see technical data on page 64).

INSTALLATION INSTRUCTIONS

The minimum controls which may be installed are OPEN-STOP-CLOSE, these
controls must be installed in a location not accessible to children.
During the opening/closing manoeuvre check for correct operation and activate
the emergency stop button in case of danger.
During blackouts the boom can be released and manually manoeuvred (see
manual manoeuvre pag. 22).
• The ground must be stable enough to firmly hold the plinth and the anchor
plates.
• Where possible protect the barrier cabinet from accidental knocks by passing
vehicles.
• Work out the run of the cables according to the command and control devices
fitted and make sure the system conforms to the local standard and regulations
in force (see installation example fig. 1 pag. 2).
20
IMPORTANT REMARKS
. NOT READING THESE IMPORTANT
Attention! Only for EU customers - WEEE marking.
This symbol indicates that once the products life-span has expired
it must be disposed of separately from other rubbish. The user
is therefore obliged to either take the product to a suitable dif-
ferential collection site for electronic and electrical goods or to
send it back to the manufacturer if the intention is to replace it
with a new equivalent version of the same product.