Publicidad
Idiomas disponibles
Idiomas disponibles
• Remove the pull cable starter (17) from the hook.
Release the quick-release levers (5) and fold down
the upper push bar (4). Make sure that the cables
are not bent during this process.
• Wedge a few layers of corrugated cardboard be-
tween the upper and lower push bars and the en-
gine to prevent any chafing.
• The product must be secured against tipping and
slipping during transport in vehicles in order to pre-
vent damage and injuries.
12. Storage
Clean and maintain the unit before storage.
Store the device and its accessories in a dark, dry and
frost-free place that is inaccessible to children. The op-
timum storage temperature lies between 5 and 30 ˚C.
Store the power tool in its original packaging.
Cover the power tool to protect it from dust or mois-
ture. Store the operating manual with the power tool.
• Never store the lawnmower with petrol in the tank
inside a building in which petrol fumes may come
into contact with naked flames or sparks.
• Allow the engine to cool down before you put the
lawnmower in an enclosed area.
• In order to avoid fire hazards, keep the engine, ex-
haust pipe and the area around the fuel tank free of
grass, leaves and leaking grease (oil).
Preparing the lawnmower for long-term storage
Warning: Do not remove the petrol in enclosed spac-
es, near fire or when smoking. Petrol fumes can
cause explosions and fire.
• Empty the fuel tank with a petrol extraction pump.
• Start the engine and let it run until the remaining
petrol is used up.
• Change the oil at the end of every season. To do
so, remove the used engine oil from a warm engine
and refill with fresh oil.
• Remove the spark plug from the cylinder head.
• Fill the cylinder with approx. 20 ml of oil from an
oil can.
• Slowly pull back the starter handle, which will bathe
the cylinder wall with oil.
• Attach the spark plug again.
• Clean the cooling fins of the cylinder and the housing.
• Be sure to clean the entire device to protect the
paint.
• Store the device in a well-ventilated place.
Battery and battery charger
Disconnect the battery charger and store it in a cool,
dry place when not in use. In humid environments,
corrosion of terminals and electrical contacts may
occur. If stored for a long time at high temperatures
(50°C), the battery may be permanently damaged.
Check electrical terminals and contacts on battery
and battery charger.
Wipe with a clean cloth or blow clean with com-
pressed air.
Normal charging may be required after storage. To
check the available charge, press the battery level
indicator button (E) and charge if necessary. See the
battery level indicator section.
13. Maintenance
Ensure that the unit is in good working order during its
entire service life. Improper maintenance may lead to
life-threatening injuries.
• Regular, careful servicing is required to guarantee
the safety level and performance of the device.
• Make sure that all nuts, bolts and screws are se-
curely tightened so that the device is in a safe work-
ing condition.
• Regularly check the catch basket for signs of wear
and loss of functionality.
• Regularly clean the catch basket with water and let
it dry thoroughly.
• For safety reasons, replace worn or damaged
parts.
• When storing the machine for a longer period of
time or when maintaining it, the fuel tank must be
emptied. This should only be done outdoors using
a petrol suction pump (available from DIY shops).
m WARNING
Never work on or touch conducting parts on the ig-
nition unit with the engine running. Always remove
the spark plug connector from the spark plug before
starting any work of care or maintenance. Never per-
form any work on the machine while it is running. Any
work not described in this operating manual must be
performed by an authorised service workshop only.
Attention!
Always shut the engine down and remove the spark
plug connector before carrying out any maintenance
work.
Wheel axles and wheel hubs
• These should be lightly greased once a season.
Blade
For safety reasons, only have your mowing blade
sharpened, balanced and fitted by an authorised spe-
cialist workshop. For optimum results it is recommend-
ed that the blade should be inspected once a year.
Changing the blade (fig. 17)
When changing the cutting tool, only use original re-
placement parts.
Wear gloves to avoid cut injuries while changing the
blade.
www.scheppach.com
GB | 39
Publicidad
