PROFLO PF1825WH Instrucciones De Instalación

Installation Instructions
Instructions d'installation
Instrucciones de Instalación
Wall Hung Urinal / Urinoir mural /
Mingitorio Suspendido en Pared
PF1825WH
Follow flush valve manufacturers installation instructions. This fixtures requires 25 psi minimum water pressure. Refer to all local plumbing and building codes before installation.
Veuillez suivre les instruction d'installation du fabricant du robinet de la chasse d'eau. Cet équipement exige une pression d'eau minimum de 25 psi. Veuillez vous référer à tous les
codes locaux de plomberie.
Siga las instrucciones de instalación del fabricante de la válvula de descarga. Estas conexiones requieren una presión mínima de agua de 172kPa [25 PSI]. Refiérase a todos los códigos
de plomería
1. Turn water supply off.
2. Install or relocate the supply line wand
waste pipe to conform to rough in
dimensions
3. Install shut off valve, (not included) per
manufacturers instructions
4. Insure there is appropriate construction
framing to support urinal (figure 1).
5. Install the wall hangers according to the
rough in dimensions by marking each hole
then drilling a pilot hole.
6. Apply thread sealant tape to the pipe
threads and install the female collar to the
waste pipe.
7. Place the gasket onto the female collar
with the beveled surface facing away from
the collar.
8. Gently place the urinal on the hanger(s) as
supplied and installed.
9. Secure the urinal to the female collar with
the screws and washers provided.
10. Install the flush valve per the manufactures
instructions
11. Connect the water supply and waste pipe
connections
17-11/16"
17-11/16" (450 mm)
17-11/16"
(450 mm)
(450 mm)
3-3/4"
3-3/4" (95 mm)
3-3/4"
4-1/8" (105 mm)
4-1/8"
(95 mm)
95 mm)
(105 mm)
(105 mm)
1-5/16"
1-5/16" (33 mm)
1-5/16"
(33 mm)
(33 mm)
© 2011 Ferguson Enterprises, Inc. All Rights Reserved
1. Coupez l'alimentation d'eau.
2. Installez ou relogez le tuyau d'alimentation
et le tuyau de vidange pour qu'ils soient
conformes aux dimensions de la plomberie
brute.
3. Installez un robinet d'arrêt (non fourni)
conformément aux instruction du fabricant.
4. Assurez-vous que la structure de la
construction
(figure 1).
5. Installez les supports muraux conformément
aux dimensions de la plomberie brute en
marquant chaque trou, puis en perçant un
trou pilote.
6. Appliquez un ruban à joint fileté sur les filets
du tuyau de vidange puis installez le collier
femelle sur le tuyau de vidange.
7. Placez le joint sur le collet femelle avec la
surface biseautée tournée de l'autre côté
du collet.
8. Installez délicatement l'urinoir sur les
supports fournis et installés.
9. Fixez l'urinoir au collet femelle avec les vis
et les rondelles fournies.
10. Installez le robinet de la chasse d'eau
3-3/4"
(95 mm)
conformément
17-11/16"
(450 mm)
fabricant.
11. Connectez le tuyau d'alimentation d'eau et
le tuyau de vidange.
3-3/4"
(95 mm)
(105 mm)
11-13/16"
11-13/16" (300 mm)
1-5/16" 11-13/16"
(300 mm)
(300 mm)
(33 mm)
5-1/2"
(140 mm)
14"
14" (368 mm)
14" 16-5/16"
(368 mm)
(415 mm)
(368 mm)
4-1/8"
11/16 * 7/16"
11/16 * 7/16" (18 * 11 mm)
11/16 * 7/16"
(18 * 11 mm)
(18 * 11 mm)
4"
4" (102 mm)
4"
(102 mm)
(102 mm)
Distributed Exclusively by Ferguson and Wolseley Canada
4"
3-3/4"
4"
(95 mm) (100 mm)
4"
(100 mm)
(100 mm)
1-5/16"
(33 mm)
peut soutenir
17-11/16"
(450 mm)
11-13/16"
(300 mm)
Figure 1
Figure 1
17-11/16"
(450 mm)
3-3/4"
4-1/8"
(95 mm)
(105 mm)
1-5/16"
(33 mm) 4-1/8"
aux instructions
(105 mm)
14"
1-5/16"
(368 mm)
(33 mm)
4-1/8"
11/16 * 7/16"
(18 * 11 mm)
4"
(102 mm)
5-1/2"
5-1/2" (140 mm)
(140 mm)
4"
(100 mm)
21-7/8"
21-7/8" (555 mm)
21-7/8"
(36 mm)
(555 mm)
(555 mm)
16-5/16"
16-5/16" (415 mm) 26" (660 mm)
26"
(415 mm) (660 mm)
(660 mm)
1-15/16"
1-15/16" (50 mm)
1-15/16"
(50 mm)
(50 mm)
17-11/16"
(450 mm)
14"
(368 mm)
4-1/8"
11/16 * 7/16"
(105 mm)
1/2"
(18 * 11 mm)
1/2" (39 mm)
1/2"
(39 mm)
(39 mm)
5/8"
1. Cierre la alimentación de agua.
2. Instale o reubique la tubería de alimentación
y tubo de drenaje a las dimensiones
aproximadas
3. Instale la válvula de paso, (no incluida)
según las instrucciones del fabricante
4. Cerciórese que el apoyo de construcción
es apropiado para soportar el mingitorio
l'urinoir (figura 1).
5. Instale los colgadores de pared de acuerdo
11-13/16"
con las
(300 mm)
marcando cada orificio y barrenando un
orificio piloto.
11-13/16"
6. Aplique cinta selladora de roscas a las
(300 mm)
cuerdas del tubo e instale el collarín
hembra al tubo de drenaje.
7. Coloque la junta en el collarín hembra con
5-1/2"
(140 mm)
la superficie biselada viendo al sentido
opuesto del collarín.
Figure 1
14"
8. Coloque con cuidado el mingitorio en el (los)
(368 mm)
colgador(es) ya suministrados e instalados.
9. Asegure el mingitorio al collarín hembra con
5-1/2"
16-5/16"
14"
(140 mm)
11/16 * 7/16"
los tornillos y arandelas proporcionados.
(415 mm)
(368 mm)
(18 * 11 mm)
10. Instale la válvula de descarga según las
4"
instrucciones del fabricante
(102 mm)
21-7/8"
11/16 * 7/16"
du
11. Conecte las conexiones de suministro de
(555 mm)
(18 * 11 mm)
1-15/16"
agua y drenaje.
(50 mm)
16-5/16"
4"
(415 mm) (660 mm)
(102 mm)
4"
(100 mm)
Wall Hanger
Support mural
17-1/2"
1-15/16" Colgador de
17-1/2" (445 mm) 4"
17-1/2"
(50 mm)
Pared
(445 mm) (100 mm)
(445 mm) (16 mm)
5/8"
(16 mm)
1/2"
1-3/8"
(39 mm)
1-3/8" (36 mm)
1-3/8"
14-3/16"
(36 mm)
14-3/16" (360 mm)
5/8" 14-3/16"
11-13/16" 14-3/8"
26" (360 mm)
(16 mm) (360 mm)
5-7/8"
(300 mm)
14-3/8" (365 mm)
14-3/8"
(155 mm)
(365 mm)
(365 mm)
15-1/8"
5-1/2"
(385 mm)
(140 mm)
2-13/16"
2-13/16" (72 mm)
2-13/16"
21-7/8"
(72 mm)
(72 mm)
7-7/8" (555 mm)
7-7/8" (200 mm)
7-7/8"
16-5/16"
(200 mm)
(200 mm)
(415 mm) (660 mm)
17-1/2"
1-15/16"
2-15/16"
17-1/2" (445 mm) (50 mm)
17-1/2"
4"
2-15/16" (75 mm)
2-15/16"
(445 mm)
(445 mm)
(102 mm)
(75 mm)
(75 mm)
®
Figure 1
Figure 1
Figure 1
dimensiones aproximadas
17-1/2"
®
(445 mm)
5-1/2"
(140 mm)
21-7/8"
(555 mm)
17-1/2"
(445 mm)
16-5/16" 26"
(415 mm) (660 mm)
1-3/8"
21-7/8"
(36 mm)
(555 mm)
14-3/8"
26"
(365 mm)
(660 mm)
1-15/16"
(50 mm)
1-3/8"
(36 mm)
14-3/16"
(360 mm)
14-3/8"
26"
(365 mm)
7-7/8"
Figure 1 Anchor Screw
(200 mm)
Vis d'ancrage
Tornillo de Anclaje
1/2"
(39 mm)
5/8"
2-13/16"
5-7/8"
(72 mm)
1/2"
17-1/2"
(155 mm)
7-7/8"
(39 mm)
Waste
(445 mm)
(200 mm)
Vidange
15-1/8"
Drenaje
(385 mm)
5-7/8"
(155 mm)
15-1/8"
17-1/2"
(385 mm)
2-15/16"
(445 mm)
(75 mm)
17-1/2"
(445 mm)
14-13/16"
(376 mm)
17-1/4"
(438 mm)
3-1/8"
(80 mm)
14-13/16"
1-3/8"
(376 mm)
(36 mm)
14-3/16"
17-1/4"
(360 mm)
14-3/8"
26" (438 mm)
(365 mm)
9351 09/11
2-13/16"
(72 mm)
17-
(445
1-3/
(36 m
14
(36
7-
(20
2-1
(72
17
(44
14-
(37
17
(43