Publicidad
Idiomas disponibles
Idiomas disponibles
APPLICATIONS
○ Removal of casting fi n and fi nishing of various types of
steel, bronze and aluminum materials and castings.
○ Grinding of welded sections or sections cut by means of
a cutting torch.
○ Grinding of synthetic resins, slate, brick, marble, etc.
SPECIFICATIONS
1. Power tool
Model
Voltage
Rated no-load speed
Outer dia.
Wheel
Hole dia.
Thickness
Peripheral speed
Battery available for
this tool
Weight*
* Weight: According to EPTA-Procedure 01/2014
Depending on attached battery. The heaviest weight is
measured with BSL36B18X (sold separately).
Also, the weight includes the wheel guard, side handle,
wheel washer, and wheel nut.
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
Electronic control
○ Overload protection
This protection feature cuts off the power to the motor
in the event of overloading of motor or a conspicuous
reduction in rotational speed during operation.
When the overload protection feature has been
activated, the motor may stop.
In this case, release the tool switch and eliminate causes
of overloading.
After that you can use it again.
Before
charging
While
charging
Charging
Pilot lamp
complete
(red)
Overheat
standby
Charging
impossible
G18DSL2
18 V
9000 min
-1
115 mm
125 mm
22.23 mm
6 mm
80 m/s
BSL1830C / BSL1850C
2.1 kg (BSL1830C)
2.2 kg (BSL1850C)
2.7 kg (BSL36B18X)
Indications of the pilot lamp
Lights for 0.5 seconds. Does not light
Blinks
for 0.5 seconds. (off for 0.5 seconds)
Lights continuously
Lights
Lights for 0.5 seconds. Does not light
Blinks
for 0.5 seconds. (off for 0.5 seconds)
Lights for 1 second. Does not light
Blinks
for 0.5 seconds. (off for 0.5 seconds)
Lights for 0.1 seconds. Does not light for
Flickers
0.1 seconds. (off for 0.1 seconds)
○ Restart prevention function
When the power is still switched on, the tool will not
restart when a battery is installed. This function can be
canceled once the tool is switched off .
2. Battery
Model
Voltage
Battery capacity
Available cordless
products*
Available charger
* Please see our general catalogue for details.
3. Charger
Model
Charging voltage
Weight
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger's power cord to the receptacle.
When connecting the plug of the charger to a receptacle,
the pilot lamp will blink in red (At 1-second intervals).
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in
Fig. 3.
3. Charging
When inserting a battery in the charger, the pilot lamp
will light up continuously in red.
When the battery becomes fully recharged, the pilot lamp
will blink in red (At 1-second intervals). (See Table 1)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown in
Table 1, according to the condition of the charger or the
rechargeable battery.
Table 1
11
BSL1830C
BSL1850C
18 V
3.0 Ah
5.0 Ah
BSL18 series
Sliding charger for lithium ion batteries
UC18YFSL
14.4 V–18 V
0.5 kg
Battery overheated. Unable to
charge. (Charging will commence
when battery cools)
Malfunction in the battery or the
charger
English
Publicidad
