HIKOKI G 18DSL2 Instrucciones De Manejo página 12

English
(2) Regarding the temperatures and charging time of the rechargeable battery
The temperatures and charging time will become as shown in Table 2.
Battery
Charging voltage
Type of battery
Temperatures at which the battery can be
recharged
Charging time for battery capacity, approx.
(At 20oC)
1.5 Ah
2.0 Ah
2.5 Ah
3.0 Ah
4.0 Ah
5.0 Ah
6.0 Ah
8.0 Ah
NOTE
The recharging time may vary according to the ambient
temperature and power source voltage.
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger fi rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
Regarding electric discharge in case of new batteries,
etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the fi rst and second time. This is a temporary
phenomenon, and normal time required for recharging
will be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used, the
pilot lamp of the charger lights for 1 second, does not
light for 0.5 seconds (off for 0.5 seconds). In such a case,
fi rst let the battery cool, then start charging.
○ When the pilot lamp fl ickers (at 0.2-second intervals),
check for and take out any foreign objects in the charger's
battery connector. If there are no foreign objects, it is
probable that the battery or charger is malfunctioning.
Take it to your authorized Service Center.
Table 2
Charger
V
min 22 (4 cells)
min 30 (4 cells)
min 35 (4 cells)
min 45 (8 cells/4 cells)
min 60 (8 cells)
min 75 (8 cells)
min 90 (8 cells)
min
○ Since the built-in micro computer takes about
MOUNTING AND OPERATION
Removing and inserting the
battery
Charging
Fitting and adjusting the wheel
guard
Fitting and adjusting the wheel
guard (for cutting)
Fixing the side handle
Assembling depressed center
wheel*
Assembling cutting wheel*
Switch operation
Grinding angle and grinding
method*
Cutting work
Remaining battery indicator
Check and replacing the carbon
brush
Selecting accessories
*1 sold separately
*2 WARNING
12
UC18YFSL
14.4
Li-ion
0oC–50oC
–
3 seconds to confi rm that the battery being charged with
UC18YFSL is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
Action
2
3
*4
Before use, be sure to tighten the wheel nut with the
included wrench.
NOTE
The wheel washer is specifi cally for this product. Do
not use it for any other product.
18
22 (5 cells)
30 (5 cells)
35 (5 cells)
45 (10 cells/5 cells)
60 (10 cells)
75 (10 cells)
90 (10 cells)
120 (10 cells)
Figure Page
3
4
5
6
7
8
, * 9
1 2
10
11
12
13
14
―
2
2
2
3
3
3
3
4
4
4
4
4
240