Fein ABH18-26AS Manual Del Usuario página 18

1 609 92A 7RT • 28.10.22 • PS
en
18
state of charge when the power tool is not in op-
eration.
Press the button for the battery charge indic-
ator or to show the state of charge. This is
also possible when the battery is removed.
If no LED lights up after pressing the button for
the battery charge indicator, then the battery is
defective and must be replaced.
Battery model GBA 18V...
LED
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LED
5 × continuous green light
4 × continuous green light
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × flashing green light
Recommendations for Optimal Handling
of the Battery
English
Protect the battery against moisture and water.
Only store the battery within a temperature
range of −20 to 50 °C. Do not leave the battery in
your car in the summer, for example.
Occasionally clean the ventilation slots on the
battery using a soft brush that is clean and dry.
A significantly reduced operating time after char-
ging indicates that the battery has deteriorated
and must be replaced.
Follow the instructions on correct disposal.
Assembly
English
Remove the battery from the power tool
u
before carrying out work on the power tool
(e.g. maintenance, changing tool, etc.). The
battery should also be removed for trans-
port and storage. There is risk of injury from
unintentionally pressing the on/off switch.
Auxiliary handle
English
Do not operate your power tool without
u
the auxiliary handle (17).
u
Swivelling the auxiliary handle (see figure A)
You can swivel the auxiliary handle (17) to any
angle for a safe work posture that minimises fa-
tigue.
– Turn the lower gripping end of the auxiliary
English
Capacity
60–100 %
30–60 %
Selecting drill chucks and tools
5–30 %
Hammer drilling and chiselling require SDS-plus
0–5 %
application tools that are inserted into the SDS-
plus drill chuck.
English
For drilling without impact in wood, metal,
ceramic and plastic as well as for screwdriving,
tools without SDS‑plus are used (e.g. cylindrical
shank drill bits). For these tools, a keyless chuck
Capacity
or a keyed chuck are required.
80–100 %
Changing the Tool
60–80 %
The dust protection cap (3) largely prevents the
40–60 %
penetration of drilling dust into the tool holder
20–40 %
during operation. When inserting the tool, make
5–20 %
sure that the dust protection cap (3) does not
become damaged.
0–5 %
u
Changing the tool (SDS plus)
Inserting SDS-plus application tools
(see figure B)
The SDS-plus drill chuck enables you to change
the application tool easily and conveniently
without needing to use additional tools.
– Clean and lightly grease the insertion end of
– Insert the application tool into the tool holder
– Check the latching by pulling the tool.
As a requirement of the system, the SDS-plus ap-
plication tool can move freely. This causes a cer-
tain radial run-out at no-load, which has no ef-
fect on the accuracy of the drill hole, as the drill
bit centres itself upon drilling.
Removing SDS-plus application tools
(see figure C)
– Push the locking sleeve (4) back and remove
Make sure that the auxiliary handle is al-
ways tightened. Otherwise you could lose
control of the power tool when working.
handle (17) anticlockwise and swivel the auxili-
ary handle (17) into the required position.
Then turn the lower gripping end of the auxili-
ary handle (17) clockwise to retighten it.
Make sure that the retaining strap of the auxili-
ary handle slots into the corresponding groove
of the housing.
English
Replace a damaged dust protection cap im-
mediately. It is recommended that you
have use an after-sales service for this.
English
the application tool.
while turning it until it locks automatically.
English
the application tool.
English
English
English