Publicidad
Idiomas disponibles
Idiomas disponibles
EN
List of parts
1 Multifunctional brush
2 Brush cover
3 Remote control
4 Hepa filter + foam filter
5 Wiping cloth
1
2
3
4
6
5
KEY FEATURES
Cleaning / ON/OFF
• Press briefly to start or pause cleaning.
• Press and hold for 3 seconds to switch the appliance
on or off.
• Long press for 15 seconds to force the appliance to
shut down under unusual circumstances.
Charging / Local cleaning
• Press briefly to start or pause charging.
• Long press to start local cleaning.
Indicator light
• Blue: Normal operation or charging
• Red: Abnormal condition or low battery
• Purple: The device is not connected to the network
Wi-Fi reset
• Press both buttons simultaneously for 3 seconds.
INSTALLATION
1. Connect the power cord.
Note:
• Provide a space of min. 6 cm from the wall, min. 0.5 m
on both sides of the docking station and min. 1.5 m in
front of the station.
6 Side brush
7 Cleaning brush
8 Replacement bag
9 Wiping module
10 2in1 tray
7
10
8
9
• If the power cord is stretched vertically to the ground,
the appliance may pull it out and the docking station
may be switched off.
• In normal condition, the charging indicator light is on
when switched on, and off when charged.
2. Do not move the docking station or expose it to
direct sunlight.
Note: Direct sunlight will interfere with the docking
station signal and the appliance may not return to the
docking station properly.
3. Installing the side brush
Make sure the left side brush (L) and right side brush
(R) markings correspond to the L and R markings on
the bottom cover. Push the side brushes L and R until
you hear a "click" sound.
4. Putting the appliance into operation and charging
To switch the robot on, press and hold the button
If the power indicator light is normally on, charge the
robot in the docking station.
Note: If the appliance does not start due to a low
battery, charge it in the docking station and it will start
automatically. Normally, the appliance can only operate
when the battery level is ≥20 %.
5. Connecting a mobile app (you can skip this step)
Read the instructions for connecting Wi-Fi and connect
the mobile app.
6. Start of cleaning
After switching on the robot, briefly press the button
on the robot or start cleaning using the mobile app
(you can pause the appliance by pressing any button
during use).
Note:
• The sweeping robot cannot be used to remove fluids.
• If the battery charge level is less than 20 %, the
appliance cannot operate. In this case, recharge it.
• If the battery charge level is less than 20 %, the
appliance automatically returns to the docking
station.
• Before use, remove various wires (including the
docking station power cord) from the floor to prevent
outages and damage to objects or wires when the
appliance catches these wires.
7. Installing the wiping module
a) Installing the wiping cloth: Stick the wiping cloth
straight to the bottom of the wiping module.
Wiping module
Note: Clean the wiping cloth after use to keep it in good
condition.
b) Fill the 2-in-1 container with water: Open the cover
and fill the water tank with water.
.
2-in-1 container
c) Install the module:
Press and hold the button in the centre of the
container and slide it horizontally along the back
of the robot. The 2-in-1 container is installed in
place when you hear a "click" sound and a voice
announcement from the appliance. After installing
the 2-in-1 container, insert the wiping module. Once
you hear a "click" sound, the module is correctly
inserted.
8. Removing the wiping module
Once the robot has completed its work, press the
latches on both sides, pull backwards and remove
the wiping module, empty the water from the 2-in-1
container and clean the cloth (do not move or flip the
robot during cleaning).
9. Instructions for using the wiping module
• Do not use the wiping module unless supervised.
• For safety, make sure the wiping module is removed
when charging or when not in use.
• Do not attempt to wipe the carpet.
• For a better wiping effect, the wiping module should
be used after sweeping or vacuuming the floor three
times.
• To refill water or clean the cloth while the appliance
is operating, pause it, remove and reinsert the wiping
module as described in steps 8 and 9. Do not move
or flip the appliance to avoid positioning errors and
map loss.
• The wiping function of the appliance is designed for
wiping and aids deep cleaning. However, it cannot
effectively remove stubborn dirt and thus replace
human power.
• We recommend soaking the wiping cloth before
mopping for better cleaning.
EN
Publicidad
