Publicidad
Idiomas disponibles
Idiomas disponibles
EN
• If the robot has a wiping module installed, the dirt
from the 2-in-1 container will not be sucked out.
USE
ON/OFF
Press and hold the button
for 3 seconds, the indicator
light comes on and the appliance starts.
Press and hold the button
for 3 seconds while the
appliance is in standby mode, the indicator light flashes
red and the appliance switches off.
NOTE: The appliance cannot be switched off while it is
being charged.
CLEANING/PAUSE
After starting the appliance, briefly press the button
the appliance or start the appliance using the mobile app
(press any button to pause the appliance).
CHARGING
Automatic mode: The appliance automatically returns to
the docking station after work. The dirt is sucked out of
the container. Then the robot heads back to the docking
station to charge.
Manual mode: When paused, press the button
briefly
to start charging or you can use your mobile app to
charge the appliance. The indicator light flashes when the
appliance is fully charged.
Note: If the appliance does not find the docking station,
it will automatically return to its original position. In this
case, place the device manually into the docking station.
COMPLETE AUTOMATIC CLEANING
Once the robot is on, it performs a search, generates
a map and intelligently divides it into areas. Then it sweeps
the areas one after the other properly, efficiently and
thoroughly along the wall and plans a curved / S-shaped
cleaning path. After cleaning, the robot automatically
returns to the charging base.
Note: Do not move the robot arbitrarily and often during
cleaning. After moving, place the robot in its original
position. When the robot is on again, it will try to take
a position itself. After successful positioning, the robot
will follow the planned path and continue working. If
positioning fails, the robot cancels the previous task,
creates a map, and cleans up again. Even if it does not find
a charging base.
LOCAL TURBO CLEANING
If a local area needs more thorough cleaning, the user
specifies an area of 1.5 x 1.5 m that he/she wants to clean
on the map. The appliance automatically moves to this
area and starts cleaning it.
LOCAL CLEANING
If you cannot control the robot using the mobile app,
move the robot manually to the place you want to clean
up. Press the button
for 3 seconds and the robot will
perform double cleaning in the area of 1.5 x 1.5 m with
the centre in its starting position.
ZONE CLEANING
Use the mobile app to set the size and location of the area
you want to clean up. The robot will clean in the areas you
have set.
ROOM CLEANING
Use the mobile app to select the rooms you want to clean.
RESTRICTED ZONE
on
Use the mobile app to set up one or more restricted
areas. The robot will not clean in these restricted areas
and will clean in others.
Note: The robot may reach the restricted area due to
positioning errors, sensor errors or other reasons.
• A permanently restricted zone may be invalidated
due to a significant change in position of the charging
base and furniture. Therefore, try not to move the
robot or otherwise interfere with its work during
cleaning.
• The permanently restricted area will be revoked as
soon as the map is restored.
NO WIPING ZONE
Use the mobile app to select a no wiping zone. If the
appliance has a wiping module installed, it will not go to
this area. If the appliance only vacuums, it will go to this
area.
CLEANING PLANNING
You can set a fixed cleaning time using the mobile app.
The appliance will automatically start cleaning at the
specified time and will return to the docking station when
completed.
WI-FI RESET
If the mobile phone cannot connect to the appliance
due to a change in router and password configuration or
other reasons, press the button
and the button
seconds at the same time until you hear the voice prompt
and the indicator lights up blue-violet and flashes slowly.
SILENT MODE
This mode and its duration can be set in the app.
CARPET TURBO
When the carpet is detected, the suction force
automatically increases to the highest level.
SETTING THE SUCTION POWER
You can switch off or adjust the suction power using the
mobile app or remote control.
Suction power can be set to a quiet, standard and high
level.
WATER FLOW SETTING
You can adjust the water flow using the mobile app. The
water flow cannot be changed via the remote control. The
water flow will be set to a medium level. Use the mobile
app to adjust the water flow.
USING THE REMOTE CONTROL
1. Automatic cleaning/pause
2. Forward movement
3. Left turn
4. Suction power adjustment
5. Quiet mode
6. Lights off/on
7. Start/stop charging
8. Turn right
9. Dust collection in the docking container
10. Adjusting water flow rates
11. Local cleaning
1
2
3
4
5
6
Note: To ensure that all the correct settings are effective,
you must point the remote control at the front of the
for 3
robotic vacuum cleaner from close proximity.
DAILY MAINTENANCE
Main brush (clean regularly)
1. Turn the appliance over and press the latch on the
main brush cover to pull it out.
2. Remove dust from inside and from inside the main
brush with a small brush and clean the main brush.
3. Reassemble the main brush and press firmly on the
cover until the latch clicks into place.
Side brush (clean regularly)
1. Turn the appliance over and pull the side brush up.
2. Remove hair and dirt and refit the side brush.
3. Make sure the left side brush (L) and right side brush
(R) correspond to the L and R symbols on the bottom
cover. Push the L and R side brushes to reinstall them.
Note: Replace the side brushes every 3 to 6 months to
ensure their cleaning effect.
Dust container and filter grid (clean regularly)
1. Press the button and pull the dust container
backwards.
7
2. Open and clean the dust container.
Cleaning the filter grid (clean regularly)
8
1. After prolonged use, remove the foam filter and HEPA
9
filter.
2. Rinse the foam filter and HEPA filter under water.
10
3. Wipe the individual parts and let them dry freely.
4. After drying, gradually install them in the correct order:
grid - foam filter - HEPA filter.
11
Note:
• Rinse the filter grid with clean water and do not add
any detergent.
• Do not clean the filter grid with a brush or fingers.
• Allow the filter grid to air dry for at least 24 hours.
Wiping module (clean after each use)
1. Remove and clean the cloth.
2. Wipe the water tank dry.
EN
Publicidad
