Concept VR3350 Manual Del Usuario página 43

EN
Error 4: Please scrub the cliff sensor, and restart me from
a new location
Error 5: Please scrub the front sensor, and restart me
from a new location
Error 6: Please scrub the right-hand sensor, and restart
me from a new location
Error 7: Please scrub the radar housing on top, and
restart me from a new location
Error 8: Please check if the bumper has been blocked in
some way
Error 9: Master, please clean the dust container and filter The dust container is full or the filter grid needs to be
Error 10: Dust container has been removed, please clean
the container and filter
Error 11: I'm stuck, please help me!
Error 12: Please place me correctly!
Error 13: Please check if my wheels have become blocked
somewhere
Error 14: Please check if the main brush has become
stuck
Error 15: Please check if the side brushes have become
stuck
Error 16: What's going on? Where is the docking station? Docking station not found or not connected.
Error 17: Oh dear! Program error, please restart me
Error 18: Error encountered initiating shutdown
Error 19: Low battery, please recharge
Error 20: To shut me down, please place me away from
the docking station
Error 21: Collecting fan motor error
Error 22: The dust bag is not installed
The cliff sensor is covered or placed at a height.
The infra-red anti-collision sensor is dirty or covered.
The wall sensor is dirty or covered.
The anti-collision radar sensor is dirty or covered.
The edge sensor or anti-collision sensor is stuck.
replaced.
After error 9 has been signalled, the user has removed
the dust container and this triggers error 10.
The robot is stuck somewhere.
The robot is tilted.
The drive wheel is stuck or tangled.
The main brush is tangled or stuck.
The side brush is tangled or stuck.
Abnormal condition due to unknown failure, restart the
robot.
The robot alerts the user and automatically shuts down
or recharges.
When the battery charge level is too low, the robot is not
in the docking station and cleaning starts (the battery
charge level is less than 10 %).
The robot was turned off while charging at the docking
station.
Try reconnecting the charging cable, if the problem
persists, contact the service department
Check that the dust bag is installed correctly.
WIRELESS CONNECTION AND COMPATIBILITY
• Jindřich Valenta - CONCEPT shall in no way be liable for any incidental, indirect or consequential damages, or for any
loss of data or loss due to information leakage during communication via wireless technology.
• Successful wireless communication cannot be 100% guaranteed on all Smart devices and Wi-Fi networks (routers).
Due to the variety of devices on the market, there may be cases where the character or specification of a given Smart
device or Wi-Fi network (router) makes connection impossible or is somehow disturbed. In addition, a number
of factors, including hardware and software configuration, also affect the success of wireless communication via
Wi-Fi network. The connection between the robot and your Wi-Fi network can also be adversely affected by the
surrounding Wi-Fi networks, which can be tuned to the same channel and thus interfere with the connection (e.g.
in housing estates, apartment buildings, etc.). These facts are not a reason to claim the appliance.
• The app is owned and operated by a third party (the "Entity") different from Jindřich Valenta - CONCEPT (the
"Seller"). No personal data is transferred to the Entity by the Seller. When registering for the app, the customer
submits personal data directly to the Entity, who becomes the administrator of personal data. The app and the
associated protection of personal data are governed by the Entity's rules.
Compatibility:
Smart device operating system - Android 5.0 and higher
- IOS 9.0 and higher
Wi-Fi network - 2.4 GHz
- WPA1 and WPA2 security (WPA2 recommended)
NOTICE: The appliance cannot be operated on IEEE 802.1X-protected Wi-Fi networks (usually corporate Wi-Fi networks).
OPERATING USING THE APP
Before you can control the device using the app, it is necessary to connect it to your phone and give it access to your
Wi-Fi network.
Recommended distance during set-up: less than 4 meters
Make sure your robotic vacuum cleaner, router, and your mobile phone are close together so that you can pair your phone
with the device with no problems.
Downloading and installing the app and pairing the device
Note: Pair the vacuum cleaner with a charged battery or directly placed in the charging station.
1. Scan the QR code below (Fig. 1) or find and download the "Concept Home" app from Google Play or App Store to
your mobile phone.
2. If you already have Concept Home, open the app, sign in, and continue with the pairing instructions.
3. Press and hold both control buttons on the vacuum cleaner at the same time until the voice signal for pairing the
robot sounds. The wifi indicator under the top cover of the vacuum cleaner will flash.
4. Then press "+" or "Add device" in the app.
5. Select the appliance from the list of appliances.
6. Fill in the name of your Wi-Fi and password (they can also be filled in automatically).
7. Continue with the application instructions
8. Go to Wi-Fi settings on your mobile device, connect to the "SmartLife-xxx" Wi-Fi and wait for it to connect.
9. Then return to the app and wait for your appliance to pair. After successful pairing, you can start controlling the
appliance using the mobile app.
EN