Publicidad
Idiomas disponibles
Idiomas disponibles
6.
Only use the tool for its intended purpose. Do
not use the tool for any other purpose.
7.
Switch off the tool and remove the battery
cartridge before:
•
cleaning or when clearing a blockage,
•
checking, carrying out maintenance or
working on the tool,
•
adjusting the working position of the
shear blades,
•
leaving the tool unattended.
Ensure that the tool is correctly located in a
8.
designated working position before starting
the tool.
Do not operate the tool with a damaged or
9.
excessively worn shear blades.
10. Always ensure that all handles and guards
are fitted when using the tool. Never attempt
to use an incomplete tool or one fitted with an
unauthorized modification.
Always be aware of your surroundings and
11.
stay alert for possible hazards of which you
may not be aware due to the noise of the tool.
12. Be careful not to accidentally contact a metal
fence or other hard objects during operation.
The blade will break and may cause serious injury.
13. Avoid unintentional starting. Do not carry the
tool when the battery cartridge is installed
and with finger on the switch. Make sure that
the switch is off when installing the battery
cartridge.
14. Do not grasp the exposed cutting blades or
cutting edges when picking up or holding the
tool.
15. Do not force the tool. It will do the job better and
with less likelihood of a risk of injury at the rate for
which it was designed.
16. Do not use the tool in the rain or in wet or
very damp conditions. The electric motor is not
waterproof.
17. Hold the tool firmly when using the tool.
18. Do not operate the tool at no-load
unnecessarily.
19. Before checking the shear blades, taking care
of faults, or removing foreign objects caught
in the shear blades, always switch off the tool
and remove the battery cartridge.
20. Never point the shear blades to yourself or
others.
21. If the blades stop moving due to the stuck of
foreign objects between the blades during
operation, switch off the tool and remove the
battery cartridge, and then remove the foreign
objects using tools such as pliers. Removing
the foreign objects by hand may cause an injury
for the reason that the blades may move in reac-
tion to removing the foreign objects.
22. Make sure there are no electrical cables, water
pipes, gas pipes etc. that could cause a hazard
if damaged by use of the tool.
23. Do not touch the metal parts or hot surfaces of
the tool during use or immediately after oper-
ation; they may be extremely hot and could
burn your skin. Let the tool cool down before
carrying out any work on the tool.
24. Do not use the tool on soft/unstable/slippery
ground or steep inclines. Avoid working on
ladders or at heights. Doing otherwise may
cause a risk of falling, resulting in personal injury.
25. Do not use the tool in bad weather or at night
where visibility is limited. Failure to do so
may cause fall or incorrect operation due to low
visibility.
26. Avoid working in poor environment where
increased user fatigue is expected.
27. Do not submerge the tool into a puddle.
28. Do not leave the tool unattended outdoors in
the rain.
29. When wet leaves or dirt adhere to the suc-
tion mouth (ventilation window) due to rain,
remove them.
30. Do not use the tool in the snow.
Electrical and battery safety
Do not dispose of the battery(ies) in a fire. The
1.
cell may explode. Check with local codes for
possible special disposal instructions.
Do not open or mutilate the battery(ies).
2.
Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be
toxic if swallowed.
3.
Do not charge battery in rain, or in wet locations.
4.
Do not charge the battery outdoors.
5.
Do not handle charger, including charger plug,
and charger terminals with wet hands.
6.
Do not replace the battery with wet hands.
Do not replace the battery in the rain.
7.
8.
Do not wet the terminal of battery with liquid
such as water, or submerge the battery. Do not
leave the battery in the rain, nor charge, use,
or store the battery in a damp or wet place. If
the terminal gets wet or liquid enters inside of bat-
tery, the battery may be short circuited and there is
a risk of overheat, fire, or explosion.
After removing the battery from the tool or
9.
charger, be sure to attach the battery cover to
the battery and store it in a dry place.
10. If the battery cartridge gets wet, drain the
water inside and then wipe it with a dry cloth.
Dry the battery cartridge completely in a dry
place before use.
Maintenance and storage
1.
When the tool is stopped for servicing, inspec-
tion or storage, switch off the tool and remove
the battery cartridge, and make sure all mov-
ing parts have come to a stop. Allow the tool
to cool before making any inspections, adjust-
ment, etc.
2.
Always allow the tool to cool down before
storing.
3.
When not in use, attach the blade cover to the
tool and store the tool indoors in dry, and high
locked-up place, out of reach of children.
4.
Maintain the tool with care. Keep cutting edge
sharp and clean for best performance and to
reduce the risk of injury. Follow instructions
for lubricating and changing accessories.
Keep handles dry, clean, and free from oil and
grease.
13 ENGLISH
Publicidad
