Publicidad
Idiomas disponibles
Idiomas disponibles
English
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
Wh ...................... watt hours
Ah ....................... amp hours
or AC ........... alternating current
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. These tools are factory tested; if
this tool does not operate, check power supply.
ASSEMBLY AND ADJUSTMENTS
WARNING:
serious personal injury, turn unit off and disconnect
it from power source before making any adjustments
or removing/installing attachments or accessories. An
accidental start-up can cause injury.
Blower Tube Assembly (Fig. B)
WARNING:
without tube securely in place. Never reach down into
housing through tube hole.
WARNING:
disconnect it from power source when you leave blower
unattended or when storing, checking, adjusting, cleaning, or
working on blower.
1. To attach the blower tube
up the peg
of the power head with the notch
8
blower tube opening as shown in Fig. B.
2. Push the blower tube onto the power head until the
tube locks engage the blower tube and an audible click
is heard.
3. Pull on the tube to ensure it is securely in place.
4. To remove the blower tube, squeeze both tube lock
tabs
on the side of the power head and pull the blower
4
tube off.
Attaching an Extension Cord (Fig. C)
WARNING:
switch is not engaged to reduce the risk of starting the
appliance accidentally.
A cord retention hook
6
handle on the power head.
1. Near the end of the extension cord, fold the extension
cord to create a loop.
2. Feed the loop into the cord retainer housing
shown in Fig. C.
6
PSI....................... pounds per square
inch
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation–
do not stare into
the light
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
..................... do not expose to
rain
To reduce the risk of
Do not operate blower
Always turn unit off and
3
to the power head
9
Ensure the ON/OFF
is incorporated into the rear of the
10
3. Hook the loop onto the cord retention hook
in the cord retainer.
4. Plug the extension cord into the unit.
OPERATION
WARNING:
serious personal injury, turn unit off and disconnect
it from power source before making any adjustments
or removing/installing attachments or accessories. An
accidental start-up can cause injury.
Proper Hand Position (Fig. D)
WARNING:
personal injury, ALWAYS use proper hand position as shown.
WARNING:
personal injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the power
head handle
WARNING:
without blow tube securely in place. Never reach down into
housing through tube hole.
WARNING:
Wear a filter mask if the operation is dusty. Use of rubber
gloves and substantial footwear is recommended when
working outdoors. Keep long hair and loose clothing away
from openings and moving parts. For household use only.
WARNING:
the tool off, wait 10 seconds for the fan to stop rotating
before removing the blower tube.
• Always ensure the blower is switched OFF and
disconnected from the power supply when:
- You leave blower unattended.
- Clearing a blockage.
- Checking, adjusting, cleaning or working on blower.
• Only use blower in daylight or good artificial light.
5
, line
Switching ON/OFF (Fig. A, D)
of the
WARNING:
product firmly when switching on.
CAUTION:
self or bystanders.
Your blower is fitted with a 2-speed ON/OFF switch located
on the top of the power head handle
• To switch the blower ON, slide the ON/OFF
forward to position 1.
• To operate blower in high speed, slide the ON/OFF
switch forward to position 2.
• To switch the blower off, slide the ON/OFF
MAINTENANCE
WARNING:
serious personal injury, turn unit off and disconnect
as
it from power source before making any adjustments
To reduce the risk of
To reduce the risk of serious
To reduce the risk of serious
.
2
Do not operate blower
Always wear safety glasses.
Cut hazard. When turning
Use both hands to grip the
Do not point unit discharge at
2
To reduce the risk of
6
so it rests
.
1
switch
1
1
switch back.
Publicidad
