EHEIM professionel 4+ 250 Instrucciones De Uso página 23

English
10. Insert the prefilter (4) with the blue filter mat (1) (place onto supports fi arrows). 11. Attach the pump head
(17) (observe fitting position) and close the locking clips (8).
Note: Use original EHEIM hoses only.
12. Attach the pre-assembled hose accessories (see II) to the aquarium. 13. Cut hoses (23) to the desired length and attach
to the fittings. 14. Plug the hoses (24) onto the safety adapter (13) down to the limit stop. 15. Attach the hose locking
device (11). 16. Push the safety adapter (13) into the pump head (17) until it audibly latches. 17. Set the locking lever (12
to „ON". 18. Assure the the nozzle pipe (26) is suspended above the water surface. 19. Rapidly press the suction aid (16)
several times consecutively until the filter tank (10) automatically fills with water (no water must be present in the prefilter!).
20. Plug in the power supply unit (30) at the pump head (17) (only in professionel 5e - 350 Type 2274). 21. Plug in the
power cable (31) of the filter Caution: Operate the heater only (by plugging in the heater power cable) when the water starts
circulating and the filter supplies water 22. To vent the priming aid (16) press again 1 or 2 times and push the nozzle tube
(26) into the desired position.
6. Operation (only on professionel 5e 350, Type 2274)
System Requirements
WiFi-enabled terminal device (smartphone, tablet, notebook etc.)
6.1 Creating a Network
Insert the plug of the mains cable into the mains socket.
• Status LED (20) flashes white: Network of the unit is being created.
• Status LED lights up blue: Device has created network.
6.2 Connecting to the Wi-Fi network
Open the network settings of your terminal device (smartphone, tablet, notebook etc.). Connect the terminal device to
the WiFi network (SSID) EHEIM Filter XXXXXXXX. Enter the network security key.
You will find the label with the SSID as well as the network security key (Key) on the bonnet of the filter or scan the
QR code 1 to establish a connection.
6.3 Calling up the website
Open your web browser and enter the following address: http://192.168.1.1
You can also use the QR code 2 (see label) to open the web page in the browser.
6.4 Initial configuration
Select the desired language from the language selection and follow the instructions for the initial configuration.
Reset
Touch the touch field below the status LED (20) with a finger for approx. 8-10 seconds until the status LED lights up in
a colour change. If the status LED lights up green, the reset is completed and the unit creates its network again. Network
security key (Key) and QR code 1 are invalid. Connection to the network is possible without a network security key.
Meaning Status LED (20)
• Status LED flashes white: Network is being created.
• Status LED lights up blue: Device has created network and is ready for operation.
• Status LED lights up green: Device is connected to another EHEIMdigital device.
Thermofilter professionel 4+ - 250 T (Typ 2371) / 350 T (Typ 2373),
7.
Only thermofilter: 33. Control indicator („ON" / „OFF") 34. LED indicator in Celsius (°C) 35. Status indicator for
target temperature in Celsius (°C) 36. Pushbutton 37. Display in Fahrenheit (°F) 38. Heating spiral.
Setting range of the target temperature
Factory setting of the target temperature
Factory setting of the temperature unit
18° – 34°C
24°C / 75°F
Celsius (C) / Fahrenheit (F)
23
see III
64° – 93°F