Front View; Side View; Rear View - Harman JBL CONTROL 2P Manual De Instrucciones

Features

FRONT VIEW

1. WHITE LED - Illuminates when the Control 2P is connected to a power
source and the POWER SWITCH is set to ON.
2. RED LED - Flashes intermittently when the Control 2P approaches thermal
protect mode. When the Red LED is flashing, system volume should be
reduced. When the Red LED glows continuously, the Control 2P should be
turned-off and allowed to cool before re-powering the system.
3. SNAP-ON PEDESTAL - Use these adapters to adjust the vertical coverage
angle of the Control 2P for optimum performance in desk-top applications.

SIDE VIEW

4. VOLUME CONTROL - Adjusts the volume output of the Control 2P and
connected extension speaker.
5. HEADPHONE JACK - 3.5 mm (1/8") stereo jack for headphones.
When headphones are connected to this jack, the speakers are automatically
muted. CAUTION: listening to music at high volume levels using head-
phones may lead to hearing damage.

REAR VIEW

6. POWER SWITCH - Turns the Control 2P system OFF and ON.
7. MOUNTING BRACKET ATTACHMENT POINT - This 1/4" x 20 TPI
(threads per inch) fitting allows attachment of the optional MTC-2P
wall mounting bracket.*
8. SAFETY HOOK - Attach suitable safety cable to this hook when
mounting speakers.*
9. MASTER XLR/1/4" INPUT - A combination XLR and TRS balanced
line-level input. 3-pin XLR or 1/4" TRS connectors can be connected to
this jack. Note: if a signal is connected to this jack only, sound will only
emanate from the Control 2P Master loudspeaker. Signal will not be fed
to both loudspeakers.
10. EXTENSION SPEAKER XLR/1/4" INPUT - A combination XLR and
TRS balanced line-level input. 3-pin XLR or 1/4" TRS connectors can be
connected to this jack. NOTE: If a signal is connected to this jack only,
sound will only emanate from the Control 2P Extension loudspeaker.
Signal will not be fed to both loudspeakers.
11. DC POWER INPUT - Input connector for the external power supply.
12. RCA INPUTS - Unbalanced input jacks for RCA style connectors.
NOTE: if a signal is connected to the red RCA input jack, sound will
only emanate from the Control 2P Master loudspeaker. If a signal is
connected to the white RCA input jack, sound will only emanate from the
Control 2P Extension loudspeaker. NOTE: Do not simultaneously connect
sources to the RCA inputs and the XLR/1/4" inputs. Doing so may
compromise performance.
13. HF ADJUST SWITCH - Use this switch to adjust the amount of high
frequency produced by the loudspeaker(s). The 0 dB setting is the normal
setting. Use the -2 dB setting to decrease the amount of high frequency
produced by the speakers. Use the +2 dB setting to increase the amount
of high frequency produced by the speakers.
14. EXTENSION SPEAKER JACK - 1/4" output jack for connection of the Control 2P Extension loudspeaker
to the Control 2P Master loudspeaker. When the extension speaker cable plug (included) is removed from this jack,
the extension speaker amplifier channel is automatically muted.
15. SAFETY BAR - An attachment point for connection of an optional safety cable or lanyard from an
independent secured mount point.*
4
1
2
3
4
5
8
7
Serial Number:
9
Master
BALANCED INPUTS
ON
1/4 " T .R.S./XLR
6
Extentsion 10
Spea k er
P O WER SWITCH
12
Master
-2dB 0dB +2dB
T ip
Extention
11
Spea k er
HF Adjust Slee v e
UNBALANCED
P O WER IMPUTS 13 14
EXTENTION
SPEAKER
19 VCD
3.4A
Min Max