Troubleshooting Guide - DeWalt D51420 Manual De Instrucciones

Compressor will be sufficient for tools at all production rates.
Le compresseur peut actionner tout outil, quel que soit le taux de production.
El compresor será suficiente para las herramientas a todo índice de producción.
Compressor will be sufficient at slow or moderate production rates, but may have difficulty at very rapid rates.
Le compresseur peut actionner des outils à des taux de production faibles ou modérés, mais peut avoir de la difficulté à
des taux très élevés.
El compresor será suficiente a índices de producción lentos o moderados pero tendrá dificultad con índices demasiado
rápidos.
Compressor will be adequate only when tools are utilized at slow production rates (punch-out or occasional use).
Le compresseur ne sera vraiment efficace que lorsque les outils sont utilisés à de faibles taux de production
(p. ex., lors de travaux rapides ou occasionnels).
El compresor será adecuado sólo cuando las herramientas sean utilizadas a índices de producción lentos
(perforación o uso ocasional).
Not Recommended
Taux non recommandés
No se recomienda
CARACTÉRISTIQUES DES ATTACHES
ESPECIFICACIONES PARA GRAPAS
Fastener Lengths
Longueur
Largos de grapas
Fastener Gauge
Calibre
Calibre de grapas
Crown Width
Largeur de tête
Ancho de la cabeza
Fastener Stick Angle
Angle du bâton
Ángulo de grapas
Height / Hauteur /Altura
Width / Largeur / Ancho
Length / Longueur / Largo
Weight / Poids / Peso
Recommended Operating Pressure
Pression d'utilisation recommandée
Presión de operación recomendada
Air Consumption per 100 cycles
Consommation d'air par 100 cycles
Consumo de aire por cada 100 ciclos
Loading capacity
Capacité de charge
Capacidad de carga
MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW. FOR MORE SERIOUS OR PERSISTENT PROBLEMS,
WARNING: TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY, ALWAYS DISCONNECT AIR FROM TOOL BEFORE ALL REPAIRS.
Trigger valve housing leaks
Top cap leaks air
Exhaust leaks
Air leaks around nose when
tool is at rest. (Driver blade in up position)
Air leaks around nose when tool is in
actuated position. (Driver blade in
down position)
Tool does not cycle in cold weather
Lack of power; sluggish
Skipping fasteners; intermittent feed
Fasteners jam in tool
FASTENER SPECIFICATIONS
D51420
1/2" - 1"
(12.7 mm – 25.4 mm) (12.7 mm – 38.1 mm)
de 12,7 mm – 25,4 mm de 12,7 mm – 38,1 mm
(1/2 à 1 po) (1/2 à 1-1/2 po)
1/2 – 1 pulg. 1/2 – 1-1/2 pulg.
(12,7 mm – 25,4 mm) (12,7 mm – 38,1 mm)
18 gauge
18
Calibre 18
1/4"
6,35 mm (1/4 po) 6,35 mm (1/4 po)
6,35 mm (1/4 pulg.) 6,35 mm (1/4 pulg.)
Straight
Droit
Recto
CARACTÉRISTIQUES DE L'OUTIL
ESPECIFICACIONES DE LA HERRAMIENTA
18 gauge Narrow Crown Stapler
8.1'' (206 mm) / 206 mm (8,1 po) / 8,1 pulg. (206 mm)
2.6'' (67 mm) / 67 mm (2,6 po) / 2,6 pulg. (67 mm)
9.6'' (245 mm) /245 mm (9,6 po) / 9,6 pulg. (245 mm)
2.6 lbs. (1.179 kg) / 1.179 kg (2,6 lb) / 2,6 lb (1.179 kg)
70 - 120 psig (4.9 - 8.3 bar, 5 to 8.5 kg/cm
2
de 5 à 8,5 kg/cm (70 à 120 lb/po
70 - 120 psi (4,9 – 8,3 bar, 5 a 8,5 kg/cm
2.1 cfm @ 100 psi
3
2,1 pi /mn @ 100 lb/po
2,1 cfm @ 100 psi
Up to 100 fasteners
Jusqu'à 100 attaches
Hasta 100 grapas

Troubleshooting Guide

CONTACT A D WALT SERVICE CENTER OR CALL 1-(800)-4-DEWALT.
E
O-ring or valve stem failure
Loose cap screws
Damaged or worn gasket or o-ring
Main seal or o-ring damaged, debris in tool.
Damaged or worn o-rings
Damaged or worn bumper
Tool not receiving air
Valve may be frozen
Damaged or worn o-rings
Broken or damaged driver blade
Low air pressure
Lack of lubrication
Damaged or worn o-rings
Exhaust port blocked or clogged
Air restricted
Lack of lubrication
Nosepiece screws loose
Wrong size/angle fasteners
Dirty magazine
Worn magazine
Broken or damaged driver blade
Trigger valve o-ring worn or damaged
Worn piston o-ring
Worn or damaged pusher spring
Magazine loose
Driver channel in nose piece worn
Wrong size/angle fasteners
Magazine loose
Worn driver blade
Nosepiece screws loose
Fasteners not feeding properly
D51422
1/2" - 1-1/2"
18 gauge
18
Calibre 18
1/4"
Straight
Droit
Recto
TOOL SPECIFICATIONS
D51420
2 )
2
ou 4,9 à 8,3 bar)
2 )
2
Replace valve using: Trigger Valve Kit:
Tighten cap screws using appropriate Allen wrench
Replace gasket/o-rings using: O-ring Repair Kit
Replace gasket/o-rings using: O-ring Repair Kit
Replace gasket/o-rings using: O-ring Repair Kit
Replace bumper using: Bumper Kit
Check air supply
Warm up tool
Replace gasket/o-rings using: O-ring Repair Kit
Replace Driver Blade Kit
Check air supply
Lubricate tool using approved pneumatic tool oil
Replace gasket/o-rings using: O-ring Repair Kit
Disconnect air, remove exhaust plate from top of tool, clean port
Check air supply and couplers
Lubricate tool using approved pneumatic tool oil
Tighten nosepiece screws using appropriate Allen wrench
Use only recommended fasteners
Clean magazine track and nosepiece
Replace magazine
Replace Driver Blade Kit
Replace valve using: Trigger Valve Kit
Replace Piston o-ring using: O-Ring Repair Kit
Replace spring
Check that magazine latch is holding firmly
Replace nosepiece
Use only recommended fasteners
Check that magazine screws are holding firmly
Replace Driver Blade Kit
Tighten nosepiece screws using appropriate Allen wrench
Ensure fasteners are feeding properly into nose
Portable
Handcarry
3.2 - 4 CFM
Petit
outil
portatif
5,4 – 6,8 CMM
(3,2 – 4 CFM)
Portátil
5,4 – 6,8 CMM
(3,2 – 4 CFM)
1
2
3
4
5
6
7
8+
D51422
18 gauge Narrow Crown Stapler
9.1'' (232 mm) / 232 mm (9,1 po) / 9,1 pulg. (232 mm)
2.8'' (70 mm) / 70 mm (2,8 po) / 2,8 pulg. (70 mm)
10.2'' (260 mm) /260 mm (10,2 po) / 10,2 pulg. (260 mm)
3.5 lbs. (1,588 kg) / 1,588 kg (3,5 lb) / 3,5 lb (1,588 kg)
70 - 120 psig (4.9 - 8.3 bar, 5 to 8.5 kg/cm
2
de 5 à 8,5 kg/cm (70 à 120 lb/po
70 - 120 psi (4,9 – 8,3 bar, 5 a 8,5 kg/cm
3.5 cfm @ 100 psi
3
3,5 pi /mn @ 100 lb/po
3,5 cfm @ 100 psi
Up to 100 fasteners
Jusqu'à 100 attaches
Hasta 100 grapas
Industrial
5.5 HP Gas 8 HP Gas
23+ CFM
14 - 16
2 HP Elec.
CFM
8 - 9 CFM
Outil à gaz
Outil à gaz
Outil
(5,5 hp)
(8 hp)
industriel
Outil élec-
23,8 – 27,2
39,1+ CMM
trique
CMM
(23+ CFM)
(2 hp) (14 – 16
13,6 – 15,3 CFM)
CMM
(8 - 9 CFM)
Industrial
8 HP Gas
39,1+ CMM
5,5 HP Gas 23,8 – 27,2
(23+ CFM)
CMM
2 HP Elec.
(14 – 16
13,6 – 15,3
CFM)
CMM
(8 - 9 CFM)
2 )
2
ou 4,9 à 8,3 bar)
2 )
2
D51420 D51422
Cat. # Cat. #
D510005 D510005
D510001 D514221
D510001 D514221
D510001 D514221
D510003 D514223
D510001 D514221
D514202 D514222
D510001 D514221
D514202 D514222
D510005 D510005
D510001 D514221
D514202 D514222