Clarke US 1500 Manual Del Operador página 41

revised 9/2017
Item Ref. No. Qty Description
1 980657 2 Washer Lock 1/4 Std
2 56115368 2 Spring Tube
3 56201018 4 Wheel 5.00 X 1.50
4 56381964 4 Spacer
5 56381966 1 Mainframe Dust Cont-Machined NOTE 1
6 56382805 2 Wheel Plate Wldt NOTE 2 / TSB-FC-2014-004
7 56382808 2 Pivot Plate Wldt NOTE 2 / TSB-FC-2014-004
8 30739A 1 Shroud Dust
9 56384009 3 Washer-Nylon-1.125x.030
10 56393565 1 Skirt Assy
11 1 Handle, Assembly Clarke DC TSB-FC-2014-016
12 61869A 1 Axle Rear
13 976240 1 Pad-Aqua-20-5/Cs
14 980413 1 Washer Retainer
15 980673 8 Washer Flat 1/2 X 7/8 X 3/64
16 56109766 16 Screwbuttonhead 1/4-20 X .63 Sems NOTE 2 / TSB-FC-2014-004
17 80346A 2 Spring Comp 25 (US1500DC) NOTE 3 / TSB-FC-2016-278
17 56384778 2 Spring Comp 35LB (US2000DC) NOTE 4 / TSB-FC-2016-278
18 56381974 1 Decal-Motor Cover (US1500DC)
18 56381973 1 Decal-Motor Cover (US2000DC)
19 30741A 1 Cover Dust Bag
20 38737A 2 Sleeve, Split .810 Id X 1.02 OD
21 38738A 2 Spacer, .257 X 1/2 X 1
22 39872A 4 Guide, Spring
23 39873A 2 Arm, Link
24 40966A 1 Motor 1.5HP 1500 RPM 120/60 (US1500DC) / TSB-FC-2013-142 / TSB-FC-2014-004
24 41030A 1 Motor 1.1KW 1500 RPM 230V/50/60 (US1500DC)
24 40936A 1 Motor 1.5HP 2000 RPM 120/60 (US2000DC) / TSB-FC-2013-142 / TSB-FC-2014-004 / TSB-FC-2016-277
24 41031A 1 Motor 1.1KW 2000 RPM 230V/50/60 (US2000DC)
25 54195A 1 Bag, Dust (Package Of 10)
26 54196A 2 Spring Extension
27 54198A 1 Pad Driver TSBCL2010-11
28 54434A 2 Clamp Cable
29 54435A 1 Gasket 2 Piece
30 61849A 1 Pedal, Release
31 61870A 1 Axle, Pivot
32 61892A 1 Pin, Load Spring 1/2 X 5.75
33 73323A 1 Label Motor Clarke
34 962957 2 Screw, 10-16 x 1/2 Self Tap
35 80292A 3 Screw .25-20 X 1.00 Bhhr Sems
36 80295A 4 Washer Bowed
37 80297A 6 Screw 1/4-20 X 1.75 Bh Zp Sems
38 80378A 1 Ring Retaining External 0.750"
40 980413 4 Washer Retainer (US2000DC)
41 980413 8 Washer Retainer (US2000DC, qty of 4 on US1500DC)
MOTOR SERVICE PARTS
[ ] 56383569 1 Rectifi er-60A 600V (120V) / TSB-FC-2013-142
[ ] 46105A 1 Rectifi er (240V)
[ ] 902550 1 Bearing 6203 (Upper)
[ ] 902547 1 Bearing 6205 (Lower)
[ ] 980076 1 Wave Washer
[ ] 56384679 1 Brush Assembly Kit (120V) (contains 4 carbon brushes and springs)
[ ] 40411A 1 Brush Board Assembly (240V)
[ ] 59607A 1 Varistor (part of 40411A)
[ ] 55647A 1 Yellow Lead (part of 40411A)
[ ] 55648A 1 Red Lead (part of 40411A)
[ ] 56384679 1 Brush Assembly Kit (240V) (contains 4 carbon brushes and springs)
[ ] = Not Shown
NOTE 1: If you need to replace Mainframe 30742A or Motor Mount 30744A please order Mainframe Kit 56109767
NOTE 2: As of serial number 3000165303, the Front Axle (61871A) has been replaced by an adjustable assembly consisting of a Wheel Plate Weldt (56382805) and
a Pivot Plate Weldt (56382808). If you have a machine built prior to this serial number and would like to convert your machine to this new design please order Wheel
Adjustment Kit (56382812).
NOTE 3: Order Compress Spring Kit-1500 RPM PN 56384779 to receive two springs and installation instructions.
NOTE 4: Order Compress Spring Kit-2000 RPM PN 56384780 to receive two springs and installation instructions.
Clarke
®
Operator's Manual - Ultra Speed Burnisher
-41-
US1500DC-2000DC ASSY
FORM NO. 71280A