Roland D2 Manual Del Usuario página 101

Hold 2 (Controller number 69)
status 2nd byte
BnH 45H
Portamento control (Controller number 84)
status 2nd byte
BnH 54H
* For the functions of other controller numbers, refer to "Table of Transmitted Data" (p. 76).
Program Change
status 2nd byte
CnH ppH
pp=Program number: 00H - 7FH (prog.1 - prog.128)
* This message is not transmitted when the Tx Program Change Switch parameter is OFF.
System Realtime messages
Active Sensing
status
FEH
* Transmitted at intervals of approximately 250ms.
System Exclusive messages
Universal Non-realtime System Exclusive Messages
Identity Reply
Status Data byte
F0H 7EH, dev, 06H, 02H, 41H, 0BH, 01H,
03H, 00H, 00H, 03H, 00H, 00H
Byte Explanation
F0H Exclusive status
7EH ID number (universal non-realtime message)
dev Device ID (dev:10H(17)-1FH(32))
06H Sub ID#1 (General Information)
02H Sub ID#2 (Identity Reply)
41H ID number (Roland)
0BH 01H Device family code
03H 00H Device family number code
00H 03H 00H 00H Software revision level
F7H EOX (End of Exclusive)
* When Identity Request is received, Identity Reply message will be transmitted.
Data Set 1 DT1
status data byte
F0H 41H, dev, 00H, 0BH, 12H, aaH, bbH,
ccH, ddH, eeH, ... ffH, sum
Byte Remarks
F0H Exclusive status
41H ID number (Roland)
dev device ID (dev: 10H–1FH)
00H model ID (D2)
0BH model ID (D2)
12H command ID (DT1)
aaH address MSB
bbH address
ccH address
ddH address LSB
eeH data: The actual data to be transmitted. Multi-byte data is transmitted
in the order of the address.
: :
ffH data
sum checksum
F7H EOX (End Of Exclusive)
* For the address, size, and checksum, refer to "Examples of system exclusive messages
and calculating the checksum" (p. 107).
* Data whose size is greater than 128 bytes should be divided into packets of 128 bytes or
less and transmitted. Successive "Data Set 1" messages should have at least 20 ms of
time interval between them.
3rd byte
xxH
3rd byte
kkH
Status
F7H
status
F7H
Data Set 1 DT1
status data byte
F0H 41H, dev, 3AH, 12H, aaH,
bbH, ccH, ddH, sum
Byte Remarks
F0H Exclusive status
41H ID number (Roland)
dev device ID (dev: 10H–1FH)
3AH model ID (D2 Quick)
12H command ID (DT1)
aaH address (Status/Channel)
bbH address/Data H
ccH Data L
ddH Data E
sum checksum
F7H EOX (End Of Exclusive)
* For the address, size, and checksum, refer to "Examples of system exclusive messages
and calculating the checksum" (p. 107).
* Transmission of consecutive addresses is not possible.
3. Data reception (Sequencer section)
3.1 Messages recorded during recording
Channel voice messages
Note Off
status 2nd byte
8nH kkH
9nH kkH
Note On
status 2nd byte
9nH kkH
vv=Note On velocity: 01H - 7FH (1 - 127)
Polyphonic Aftertouch
status 2nd byte
AnH kkH
Control Change
status 2nd byte
BnH kkH
kk=control number: 00H–78H (0–120)
Program Change
status 2nd byte
CnH ppH
pp=Program number: 00H–7FH (prog.1–prog.128)
Channel Aftertouch
status 2nd byte
DnH vvH
Pitch Bend Change
status 2nd byte
EnH llH
mm,ll=Pitch Bend value: 00 00H–40 00H–7F 7FH (-8192–0–+8191)
Channel Mode messages
All Sound Off (Controller number 120)
status 2nd byte
BnH 78H
Reset All Controllers (Controller number 121)
status 2nd byte
BnH 79H
MIDI Implementado
status
F7H
3rd byte
vvH
00H
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
mmH
3rd byte
00H
3rd byte
00H
101