General Power Tool Safety Warnings; Safety Instructions For Mitre Saws - Makita LS0815F Manual De Instrucciones

Ocultar thumbs Ver también para LS0815F:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 73
Max. Cutting capacities (H x W) with 216 mm in diameter
Miter angle
45°
60° (right)
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
............. Read instruction manual.
............. DOUBLE INSULATION
......... To avoid injury from flying debris, keep
holding the saw head down, after making
cuts, until the blade has come to a
complete stop.
When performing slide cut, first pull
carriage fully and press down handle,
then push carriage toward the guide
fence.
............. Do not place hand or fingers close to the
blade.
.......... Adjust sliding fences clear of blade and
blade guard properly.
...... LASER RADIATION: Do not stare into
beam. Direct laser beam may injure your
eyes.
............... Only for EU countries
Do not dispose of electric equipment
together with household waste material!
In observance of the European Directive,
on Waste Electric and Electronic
Equipment and its implementation in
accordance with national law, electric
equipment that have reached the end of
their life must be collected separately and
returned to an environmentally
compatible recycling facility.
Intended use
The tool is intended for accurate straight and miter cutting
in wood. With appropriate saw blades, aluminum can also
be sawed.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
12
45° (left)
50 mm x 305 mm
50 mm x 215 mm
-
SAFETY WARNINGS
END326-1
General power tool safety
warnings
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.

Safety instructions for mitre saws

1. Mitre saws are intended to cut wood or wood-like
products, they cannot be used with abrasive cut-
off wheels for cutting ferrous material such as
bars, rods, studs, etc. Abrasive dust causes moving
parts such as the lower guard to jam. Sparks from
abrasive cutting will burn the lower guard, the kerf
insert and other plastic parts.
2. Use clamps to support the workpiece whenever
possible. If supporting the workpiece by hand, you
must always keep your hand at least 100 mm from
either side of the saw blade. Do not use this saw to
cut pieces that are too small to be securely
clamped or held by hand. If your hand is placed too
close to the saw blade, there is an increased risk of
injury from blade contact.
3. The workpiece must be stationary and clamped or
held against both the fence and the table. Do not
feed the workpiece into the blade or cut
"freehand" in any way. Unrestrained or moving
workpieces could be thrown at high speeds, causing
injury.
ENE006-1
4. Push the saw through the workpiece. Do not pull
the saw through the workpiece. To make a cut,
raise the saw head and pull it out over the
workpiece without cutting, start the motor, press
the saw head down and push the saw through the
ENF002-2
workpiece. Cutting on the pull stroke is likely to cause
the saw blade to climb on top of the workpiece and
violently throw the blade assembly towards the
operator.
5. Never cross your hand over the intended line of
cutting either in front or behind the saw blade.
Bevel angle
5° (right)
60 mm x 305 mm
-
-
65 mm x 305 mm
65 mm x 215 mm
65 mm x 150 mm
GEA010-2
ENB130-2

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ls0815flLs0815fln

Tabla de contenido