Accessories; Storage; Service And Repair; Disposal - RIDGID 122 Manual De Instrucciones

122/122XL Copper Cutting and Prep Machines
Replace the motorcover. Do not use the machine with the
cover removed.
If motor does not start or the thermal overload continual-
ly trips during normal operation, the machine should be
taken to RIDGID Authorized Service Center.

Accessories

WARNING
To reduce the risk of serious injury, only use acces-
sories specifically designed and recommended for
use with the 122 and 122XL Copper Cutting and
Prep Machines such as those listed below. Other
Accessories suitable for use with other tools may be
hazardous when used with the 122 and 122XL
Copper Cutting and Prep Machines.
Catalog Model
No. No. Description
33175 2191 Cutter Wheel for Copper
34360 — Wheel Screw for 2191 Cutter Wheel
33551 122SS Cutter Wheel for Copper and Stainless Steel
10343 — Wheel Pin for 33551 Cutter Wheel
46105 — O.D. Deburring Disk
94682 — O.D. Cleaning Brush
94687 — 2" Reamer Cone Assembly
36662 301A Model 301A Foot Switch – 120V Only
42360 1206 1206 Stand
94692 — Reamer Blade
Fitting Brush and Holder
Catalog
No. Description
93747 Quick-Change Collet
93717 1 / " Fitting Brush (3 Per Pack)
2
93722 3 / " Fitting Brush (3 Per Pack)
4
93727 1" Fitting Brush (3 Per Pack)
93732 1 1 / " Fitting Brush (3 Per Pack)
4
93737 1 1 / " Fitting Brush (3 Per Pack)
2
93742 2" Fitting Brush (3 Per Pack)
12638 2 1 / " Fitting Brush (3 Per Pack) – 122XL Only
2
12643 3" - 4" Fitting Brush (3 Per Pack) – 122XL Only
93707 Fitting Brush Storage Kit Includes Mountable Storage Rack,
Quick-Change Collet, Spare Cutter Wheel and Brushes
( 1 / ", 3 / ", 1", 1 1 / ", 1 1 / , 2")
2 4 4 2
93712 Fitting Brush Holder
Further information on accessories specific to this tool can be found in
the RIDGID Catalog and online at www.RIDGID.com or www.RIDGID.eu
Machine Storage
The 122 and 122XL Copper Cutting and
WARNING
Prep Machines must be kept indoors or well covered in
rainy weather. Store the machine in a locked area that is
out of reach of children and people unfamiliar with the
machines. These machines can cause serious injury in the
hands of untrained users.
12

Service and Repair

WARNING
Improper service or repair can make machine
unsafe to operate.
The "Maintenance Instructions" will take care of most of
the service needs of this machine. Any problems not
addressed by this section should only be handled by an
authorized RIDGID service technician.
Tool should be taken to a RIDGID Independent Service
Center or returned to the factory.
For information on your nearest RIDGID Independent
Service Center or any service or repair questions:
• Contact your local RIDGID distributor.
• Visit www.RIDGID.com or www.RIDGID.eu to find
your local RIDGID contact point.
• Contact Ridge Tool Technical Service Department at
rtctechservices@emerson.com or in the U.S. and
Canada call (800) 519-3456

Disposal

Parts of the 122 and 122XL Copper Cutting and Prep
Machines contain valuable materials and can be recycled.
There are companies that specialize in recycling that
may be found locally. Dispose of the com ponents in com-
pliance with all applicable regulations. Contact your local
waste management authority for more information.
For EC Countries: Do not dispose of elec-
trical equipment with household waste!
According to the European Guideline 2002/ -
96/ EC for Waste Electrical and Electronic
Equipment and its implemen tation into nation-
al legislation, electrical equipment that is no
longer usable must be collected separately and disposed
of in an environmentally correct manner.