Handling The Usb Connector; Failure To Operate; Visit Our Website; Protecting The Lcd Panel And Screen - Pioneer AVH-X490BS Manual De Instrucciones

Precaution
WARNING

SCREEN IMAGE MAY APPEAR REVERSED.
 USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE
REAR VIEW CAMERA. OTHER USE MAY RESULT IN
INJURY OR DAMAGE.
CAUTION
The rear view mode is to use this product as an aid to keep
an eye on the trailers, or while backing up. Do not use this
function for entertainment purposes.

Handling the USB connector

CAUTION

To prevent data loss and damage to the storage device,
never remove it from this product while data is being
transferred.

Pioneer cannot guarantee compatibility with all USB mass
storage devices and assumes no responsibility for any loss
of data on media players, iPhone, smartphone, or other
devices while using this product.

Failure to operate

After-sales service for Pioneer products
Please contact the dealer or distributor from which you
purchased the product for after-sales service (including
warranty conditions) or any other information. In case the
necessary information is not available, please contact the
companies listed below.
Please do not ship your product to the companies at the
addresses listed below for repair without making advance
contact.
 USA
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760 Long Beach, CA 90801-1760
800-421-1404
For warranty information, please see the Limited Warranty
sheet included with your product.

Visit our website

Visit us at the following site:
http://www.pioneerelectronics.com
6
1 Register your product.
2 Receive updates on the latest products and technologies.
3 Download owner's manuals, order product catalogs,
research new products, and much more.
4 Receive notices of software upgrades and software updates.
Protecting the LCD panel and
screen
 Do not expose the LCD screen to direct sunlight when this
product is not used. This may result in LCD screen malfunc-
tion due to the resulting high temperatures.
 When using a cellular phone, keep the antenna of the cel-
lular phone away from the LCD screen to prevent disruption
of the video in the form of spots, colored stripes, etc.
 To protect the LCD screen from damage, be sure to touch the
touch panel keys only with your finger and do so gently.

Notes on internal memory

Before removing the vehicle battery

Some of the settings and recorded contents will not be reset.
Data subject to erasure
The information is erased by disconnecting the yellow lead from
the battery (or removing the battery itself).
 Some of the settings and recorded contents will not be reset.
Resetting the microprocessor
CAUTION
Pressing the RESET button resets settings and recorded
contents to the factory settings.
 Do not perform this operation when a device is connected
to this product.
 Some of the settings and recorded contents will not be
reset.
The microprocessor must be reset under the following
conditions:
 Prior to using this product for the first time after installation.
 If this product fails to operate properly.
 If there appears to be problems with the operation of the
system.
 If your vehicle position is shown on the map with a signifi-
cant positioning error.
1 Turn the ignition switch OFF.
2 Press the RESET button with a pen tip or other
pointed implement.
 Refer to Checking part names and functions on page 7
Settings and recorded contents are reset to the factory settings.

About this manual

This manual uses diagrams of actual screens to describe opera-
tions. However, the screens on some units may not match those
shown in this manual depending on the model used.
Meanings of Symbols Used in This
Manual
This indicates model name that are supported
X0000BT
the described operations.
This indicates to touch an appropriate soft key
on the touch screen.
This indicates to touch and hold an appropri-
HOLD ate soft key on the touch screen.
This indicates that there is a reference or
supplementary for the key or screen.
Use and care of the remote
control
Installing the battery
Slide the tray on the back of the remote control out and insert the
battery with the plus (+) and minus (–) poles aligned properly.

When using for the first time, pull out the film protruding
from the tray.