Saving The Sound Settings; Loading The Sound Settings - Pioneer AVH-X490BS Manual De Instrucciones

Audio adjustments
remove them in advance. Surrounding sounds may prevent
correct measurement of the vehicle's acoustics.
 Be sure to use the microphone for acoustical measurement
(sold separately). Using another microphone may prevent
measurement, or result in incorrect measurement of the
vehicle's acoustics.

To perform Auto EQ, the front speakers must be connected.

When this product is connected to a power amp with input
level control, Auto EQ may be impossible if the power amp's
input level is set below the standard level.
 When this product is connected to a power amp with an LPF
(low pass filter), turn the LPF off before performing Auto EQ.
Also, set the cut-off frequency for the built-in LPF of an active
subwoofer to the highest frequency.
 The distance has been calculated by a computer to provide
optimum delay to ensure accurate results. Do not change
this value.
— The reflected sound within the vehicle is strong and delays
occur.
— The LPF on active subwoofers or external amps delay the
lower sounds.
 If an error occurs during measurement, check the following
before measuring the vehicle's acoustics.
— Front speakers (left/right)
— Rear speakers (left/right)
— Noise
— Microphone for acoustical measurement (sold separately)
— Low battery
Performing Auto EQ
p Auto EQ changes the audio settings as follows:
— The fader/balance settings return to the center position.
 Refer to Using fader/balance adjustment on page 41
— "Mute Level" is set to "Off".
 Refer to Switching sound muting/attenuation on page 41
p Previous settings for Auto EQ will be overwritten.
CAUTION
Do not turn off the engine while the measurement is in
progress.
1 Stop the vehicle in a quiet place, close all the
doors, windows and sun roof, and then turn the
engine off.
If the engine is left running, engine noise may prevent correct
Auto EQ.
p If driving restrictions are detected during measurement,
measurement is canceled.
44
2 Fix the microphone for acoustical measurement
(sold separately) in the center of the headrest
of the driver's seat, facing forward.
The Auto EQ may differ depending on where you place the micro-
phone. If desired, place the microphone on the front passenger
seat and perform Auto EQ.
3 Disconnect the iPhone or smartphone device.
4 Turn on the ignition switch (ACC ON).
If the vehicle's air conditioner or heater is turned on, turn it off.
5 Switch the AV source to "Source OFF".
 Refer to Selecting a source on page 11
6 Display the "Audio" setting screen.
 Refer to Displaying the "Audio" setting screen on page 41
7 Touch [A-EQ&TA Measurement].
The "A-EQ&TA Measurement" screen appears.
8 Connect the microphone for acoustical mea-
surement (sold separately) with this product.
Plug the microphone into the AUX input jack on this product.
Use an extension cable (sold separately) if the cord of the
Microphone (sold separately) is not long enough.
9 Touch [Front Left] or [Front Right] to select the
current listening position.
10 Touch [Start].
A 10-second countdown starts.
p The Bluetooth connection is disconnected before the pro-
cess starts.
11 Exit the vehicle and keep the doors closed until
the countdown finishes.
When the countdown finishes, a measurement tone (noise)
is emitted from the speakers and the Auto EQ measurement
begins.
12 Wait until the measurement is completed.
When Auto EQ is completed, a message is displayed.
p The measurement time varies depending on the type of
vehicle.
 To stop the measurement, touch [Stop].
13 Store the microphone carefully in the glove
compartment or another safe place.
If the microphone is subjected to direct sunlight for an extended
period, high temperatures may cause distortion, color change
or malfunction.

Saving the sound settings

You can save to recall the following current sound settings:
bass boost, slope, subwoofer phase, speaker level, Graphic EQ,
HPF/LPF, listening position, crossover, time alignment.
1 Display the "Audio" setting screen.
 Refer to Displaying the "Audio" setting screen on page 41
2 Touch [Save Settings].
3 Touch [OK].
All of the current sound settings are saved.
 When you touch [Cancel], return to the "Audio"
setting screen.

Loading the sound settings

1 Display the "Audio" setting screen.
 Refer to Displaying the "Audio" setting screen on page 41
2 Touch [Load Settings].
3 Touch the item.
The following items are available:
AEQ Setting,Sound Setting.
p "AEQ Setting" is available only when you have already
performed Auto EQ measurement.
 Refer to Adjusting the equalizer curve automatically (Auto EQ)
on page 43
p "Sound Setting" is available only when you have already
saved the sound settings.
 Refer to Saving the sound settings on page 44