Roland XV-88 Manual Del Usuario página 277

Volume (Controller number 7)
Status 2nd byte
BnH 07H
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Volume: 00H - 7FH (0 - 127)
* In Performance (Zone) mode, these messages are not transmitted when Volume
parameter (ZONE/EXT CONTROL/EXT CTRL) is NO-SEND.
Panpot (Controller number 10)
Status 2nd byte
BnH 0AH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Panpot: 00H - 40H - 7FH (Left - Center - Right),
* In Performance (Zone) mode, these messages are not transmitted when Pan parameter
(ZONE/EXT CONTROL/EXT CTRL) is NO-SEND.
Expression (Controller number 11)
Status 2nd byte
BnH 0BH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Expression: 00H - 7FH (0 - 127)
Hold 1 (Controller number 64)
Status 2nd byte
BnH 40H
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0-63ÅÅOFF, 64-127ÅÅON
* When Continuous parameter (SYSTEM/CONTROL/HOLD PEDAL) is OFF, just only
00H (0FF) and 40H (0N) can be send as the control value.
Portamento (Controller number 65)
Status 2nd byte
BnH 41H
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
Resonance (Controller number 71)
Status 2nd byte
BnH 47H
n = MIDI channel number:
vv= Resonance value (relative change):
Release Time (Controller number 72)
Status 2nd byte
BnH 48H
n = MIDI channel number:
vv = Release Time value (relative change):
Attack time (Controller number 73)
Status 2nd byte
BnH 49H
n = MIDI channel number:
vv = Attack time value (relative change):
Cutoff (Controller number 74)
Status 2nd byte
BnH 4AH
n = MIDI channel number:
vv = Cutoff value (relative change):
General Purpose Controller 5 (Controller number 80)
Status 2nd byte
BnH 50H
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
General Purpose Controller 6 (Controller number 81)
Status 2nd byte
BnH 51H
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (-64 - 0 - +63)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (-64 - 0 - +63)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (-64 - 0 - +63)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (-64 - 0 - +63)
3rd byte
vvH
3rd byte
vvH
General Purpose Controller 7 (Controller number 82)
Status 2nd byte
BnH 52H
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
General Purpose Controller 8 (Controller number 83)
Status 2nd byte
BnH 53H
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
Portamento control (Controller number 84)
Status 2nd byte
BnH 54H
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = source note number: 00H - 7FH (0 - 127)
RPN MSB/LSB (Controller number 100, 101)
Status 2nd byte
BnH 65H
BnH 64H
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
When execute the GM Data Transfer, Program Change, Data Entry, and following RPN
messages will transmit.
Control Changes include RPN (Registered Parameter Numbers), which are extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any
order) should be sent in order to select the parameter, then
Data Entry (Controller numbers 6 and 38) should be sent to set the value. Once RPN
messages are received, Data Entry messages that is received at the same MIDI channel after
that are recognized as changing toward the value of the RPN messages. In order not to
make any mistakes, transmitting RPN Null is recommended after setting parameters you
need.
This device transmits the following RPNs.
RPN Data entry
MSB, LSB MSB, LSB
00H, 00H mmH, llH
00H, 01H mmH, llH
00H, 02H mmH, llH
00H, 05H mmH, llH
7FH, 7FH ---, ---
Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number: 0H - FH (ch.1 - 16)
pp = Program number: 00H - 7FH (prog.1 - prog.128)
* These messages are transmitted when Performance, Patch or Rhythm set is selected. But
not transmitted when Program parameter (SYSTEM/MIDI/TRANSMIT MIDI) is OFF.
* In Performance (Zone) mode, these messages are not transmitted when P.C# parameter
(ZONE/EXT CONTROL/EXT P.C) is NO-SEND.
MIDI Implementado
3rd byte
vvH
3rd byte
vvH
3rd byte
kkH
3rd byte
mmH
llH
Notes
Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
Master Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H
(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
Master Coarse Tuning
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
Modulation Depth Range
mm, ll: 00 00H - 06 00H
(0 - 16384 x 600 / 16384 cent)
RPN null
RPN and NRPN will be set as "unspecified."
Once this setting has been made, subsequent
277