Descargar Imprimir esta página

To Cut Grass Without A Grass Catcher Or Mulch Plug Attached; High Load Function; Maintenance - Husqvarna LC247Li Manual De Usuario

Ocultar thumbs Ver también para LC247Li:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 115
To start the product
1. Put a charged battery in battery compartment
number 1 below the battery lid. For longer operation
time, put a second charged battery in battery
compartment number 2.
2. Turn the safety key to 1. (Fig. 17)
3. Stay behind the product.
4. Press the ON/OFF button (A) on the control panel
and the green LED (B) comes on. (Fig. 31) When
you press the ON button, the two bars of the battery
indicator come on and show the levels of the two
batteries. After 2-3 seconds the battery indicator for
the battery not in operation goes off. The bar of the
battery in operation is shown for a longer time . (Fig.
32)
5. Loosen the start inhibitor. (Fig. 19)
6. Push the motor brake handle in the direction of the
handlebar. (Fig. 33)
To use the drive on the wheels (LC
347VLi)
Pull the drive bail in the direction of the handlebar to
start the drive. (Fig. 34)
Press + and - on the control panel to set the drive
speed in 4 steps. (Fig. 35)
Release the drive bail to disengage the drive, for
example when you go near an obstacle.
To use the SavE function
The product has a battery saving function (SavE) that
gives longer operation time.
1. Press the SavE button (A) to start the function. The
green LED comes on. (Fig. 36)
2. Press the SavE button again to stop the function.
The green LED (B) goes out.
The SavE function stops automatically if the ground
conditions make it necessary to have a higher output.
The SavE function starts automatically when the ground
conditions let it.

High load function

When the product cuts long or wet grass, the motor
automatically increases rpm. The motor goes back to
standard mode when high load is not necessary.
Introduction
WARNING: Before you do maintenance,
you must read and understand the safety
chapter.
16
To stop the product
The product stops automatically if you do not operate it
for 10 minutes. Always turn the safety key to 0 before
you let the product out of view.
1. Release the motor brake handle to stop the motor.
(Fig. 18)
2. Press the ON/OFF button (A) on the control panel
and the green LED (B) goes out. (Fig. 31)
3. Open the battery lid and turn the safety key to 0.
(Fig. 37)
4. To remove the battery, press the two release buttons
and pull out the battery. (Fig. 38)
5. Charge the battery if it is weak. For more
information, refer to
15 .
To get a good result
Always use a sharp blade. A blunt blade gives an
irregular result and the cut surface of the grass
becomes yellow. A sharp blade also uses less
energy than a blunt blade.
Do not cut more than ⅓ of the length of the grass.
Cut first with the cutting height set high. Examine the
result and lower the cutting height to an applicable
level. If the grass is very long, drive slowly and cut 2
times if necessary.
Cut in different directions each time to prevent
stripes in the lawn.
To cut grass without a grass catcher
or mulch plug attached
Lift up the rear cover and remove the grass catcher.
If a mulch plug and a mulch blade are attached,
remove them.
Close the rear cover before you operate the product.
When you operate the product, the cut grass discharges
below the rear cover.

Maintenance

For all servicing and repair work on the product, special
training is necessary. We guarantee the availability of
professional repairs and servicing. If your dealer is not a
service agent, speak to them for information about the
nearest service agent.
To charge the battery on page
429 - 004 - 15.11.2018

Publicidad

Solución de problemas

loading

Este manual también es adecuado para:

Lc347vli