To Cut Grass Without A Grass Catcher Or Mulch Plug Attached - Husqvarna LC 247i Manual De Usuario

4. When all LEDs on the battery have come on the
battery is fully charged. Charge the battery for
maximum 24 hours.
5. To disconnect the battery charger from the mains
socket, pull the plug, not the power cord.
6. Remove the battery from the battery charger.
Battery charging status
A Husqvarna Li-ion battery can be charged or used at all
charging levels. The battery is not damaged. A fully
charged battery will not decrease its charge when the
battery is left in the charger.
LED display
LED 1 flashes
LED 1 is lit, LED 2 flashes 25%-50%
LED 1, LED 2 are lit, LED
3 flashes
LED 1, LED 2, LED 3 are
lit, LED 4 flashes
LED 1, LED 2, LED 3,
LED 4 are lit
To start the product
1. Open the battery lid.
2. Put a charged battery in 1 of the battery holders. For
longer operation time, put a second charged battery
in the other battery holder.
3. Turn the safety key to 1. (Fig. 23)
4. Stay behind the product.
5. Push the ON/OFF button (A) on the control panel.
The display comes on. The battery indicator (B)
shows the battery charge of the 2 batteries. The
number of the battery that operates is shown
adjacent to the battery indicator. For models
LC 347iV, LC 347iVX, LC 353iV, LC 353iVX, the
display also shows the set speed. (Fig. 38)
6. Loosen the start inhibitor. (Fig. 25)
7. Push the motor brake handle in the direction of the
handlebar. (Fig. 39)
To use the drive on the wheels
(LC 347iV, LC 347iVX, LC 353iV,
LC 353iVX)
• Pull the drive bail in the direction of the handlebar to
start the drive. (Fig. 40)
• Push + and - on the control panel to set the drive
speed in 4 steps. (Fig. 41)
• Release the drive bail to disengage the drive, for
example when you go near an obstacle.
18
Charging status
0%-25%
50%-75%
75%-100%
Fully charged
To use the SavE function
The product has a battery saving function (SavE) that
gives longer operation time.
1. Push the SavE button (A) to start the function. The
SavE symbol (B) on the display comes on.
2. Push the SavE button again to stop the function. The
SavE symbol (B) on the display goes out. (Fig. 42)
The SavE function stops automatically if the ground
conditions make it necessary to have a higher output.
The SavE function starts automatically again when the
ground conditions let it.
High load function
When the product cuts long or wet grass, the motor
automatically increases rpm. The motor goes back to
standard mode when high load is not necessary.
To stop the product
The product stops automatically if you do not operate it
for 10 minutes. Always turn the safety key to 0 before
you let the product out of view.
1. Release the motor brake handle to stop the motor.
(Fig. 24)
2. Push the ON/OFF button on the control panel. All
LED lights and symbols on the display go out. (Fig.
43)
3. Open the battery lid and turn the safety key to 0.
(Fig. 44)
4. To remove the battery, push the 2 release buttons
and pull out the battery. (Fig. 45)
5. Charge the battery if it is weak. For more
information, refer to
17 .
To get a good result
• Always use a sharp blade. A blunt blade gives an
irregular result and the cut surface of the grass
becomes yellow. A sharp blade also uses less
energy than a blunt blade.
• Do not cut more than ⅓ of the length of the grass.
Cut first with the cutting height set high. Examine the
result and lower the cutting height to an applicable
level. If the grass is very long, drive slowly and cut 2
times if necessary.
• Cut in different directions each time to prevent
stripes in the lawn.
To cut grass without a grass catcher or
mulch plug attached
• Lift up the rear cover and remove the grass catcher.
• If a mulch plug and a mulch blade are attached,
remove them.
• Close the rear cover before you operate the product.
To charge the battery on page
1199 - 003 - 28.04.2020